Electrical help for homes and businessesRequest service
Emergency ElectricianCall (954) 481-0910
Emergency Electrician technician installing a pendant light in a bright coastal home

Urgent Repair

Exit Lights: What to Know and Do

Exit signs and emergency lights exist for one moment: when the normal lights fail and people need to find the way out. A sign that is dark or a light that does not come on is a life-safety defect, not a cosmetic one. This page explains what to do first, what to check, and what an electrician will look at.

Life safety first: occupied buildings and immediate steps

If a building is occupied and its exit signs or emergency lighting have failed, the question is whether people can leave safely right now. If there is a fire alarm, smoke, flame, or any emergency in progress, call 911 and evacuate by the clearest route, using flashlights and phones for light. Do not wait for repairs. Do not use elevators during a fire alarm. Guide people out in an orderly way and account for everyone.

If there is no emergency but the lights are out, think about how people would leave in the dark. Are corridors and stairwells clear? Are doors unlocked from the inside? Can people with limited mobility get out? In a retail store, a restaurant, a school, a clinic, or an assembly space, consider closing to the public until the lighting is repaired. A defect in a means of egress is a matter for the fire authority, and a building owner may have duties to correct it promptly and to protect occupants in the meantime.

Pull flashlights and battery lanterns from storage and place them where staff can reach them. Assign someone to stand at the main exits if the building is dark. Write down what you find. Then call. The sections below explain how these systems work and what an electrician checks. They do not substitute for local fire safety requirements, which are enforced by the local fire authority and may differ by city.

Emergency Electrician technician repairing and testing a wall outlet in a South Florida home

What emergency lighting and exit signs are meant to do

Emergency lighting is a system of fixtures that turn on automatically when normal power fails, and provide enough light for occupants to find their way out. Exit signs mark the routes and doors that lead out of a building. Some signs are lit all the time, and some light only when needed. Both are meant to continue working during a power failure.

Most systems depend on batteries. Self-contained emergency lights have a small battery and a charger inside the fixture. When normal power is present, the battery charges. When normal power fails, a switch connects the battery to the lamps. Exit signs may have the same arrangement, or may use another type of illumination. Some buildings use a central battery system or a generator.

Because batteries age, these systems need testing. A fixture may look fine and be lit under normal power, but have a battery that no longer holds a charge. The first test is often the real emergency. For that reason, a building owner should know how often systems are tested, who does the test, and where the records are kept. Local fire authorities set testing and record requirements, and the building owner should ask them or a fire protection contractor about the applicable schedule.

Signs that the system is failing

Look for the obvious first: an exit sign that is dark when the building has normal power, a fixture with a blinking or dim light, a test light that is off, or a fixture hanging from the wall. Some units have an indicator light that shows the charger is working. If the indicator is dark or flashing in an unusual pattern, there may be a problem with the charger or the battery.

Behavior during an actual outage is the most telling. If you have lost normal power and some emergency lights do not come on, or come on and go out within a short time, the batteries are weak. If the corridors are dark and the exit signs are dark, the system has failed entirely. Note which fixtures failed and where.

Other signs include a sweet or sharp smell near a fixture, a swollen battery, a hot casing, or melted plastic. These suggest a battery or charger fault and a potential fire hazard. Do not touch it. Keep people away, and if there is smoke or a burning smell, call 911. Otherwise, call an electrician. Do not pry open a fixture, because it contains energized parts and batteries.

Why emergency lights fail

The most common reason is old batteries. Batteries wear out whether the fixture is used or not, and a unit that is several years old may no longer hold a charge. The second is a lost power feed. Emergency lights need a continuous connection to normal power to charge, and a switched circuit, a tripped breaker, or a disconnected wire can leave the battery flat. Many units are plugged into a branch circuit that someone has turned off.

Other causes include failed chargers, burned out lamps, corroded terminals, damaged fixtures, and water intrusion. In humid and coastal areas, corrosion is common. Fixtures near outdoor doors, kitchens, or pool areas are exposed to moisture and salt. Dust and grease in kitchens can foul units. In older buildings, systems may have been altered during renovations without testing.

Sometimes the problem is the design of the system. A building may have been remodeled so that corridors changed but the lights did not. A door may have been added without a sign. Furniture, displays, or new walls may block a sign. These are not electrical faults, but they are still safety defects. A technician can point them out, and the owner should consult the fire authority about requirements.

What a manager can safely check

Walk through the building and note which signs and fixtures are lit. Most units have a test button or a key switch. Press it briefly if the manufacturer's instructions allow it, and see whether the lamps come on. Do not hold the button for long, because it discharges the battery. Do not open the fixture. If you cannot find the button, do not search around with tools.

Check that the breaker serving the emergency lights is on. In some buildings the emergency lights are on a dedicated circuit, and the breaker may be labeled. A tripped breaker can be reset once if there is no smoke or burning smell. If it trips again, stop and call. Check whether an exit sign has simply been unplugged or its switch turned off.

Do not replace batteries or lamps unless you are trained and the manufacturer's instructions allow it. Batteries and chargers are matched. Using the wrong battery can overheat the fixture. Keep a written record of what you checked and when. If the building is covered by a fire safety inspection, the records will be requested. See documenting a business outage for general advice on record keeping.

What the technician checks

A technician will inspect the fixtures and the circuit. They will check that the supply is present, that the connection is correct, and that the charger is working. They will test the battery, either by observing the unit during a controlled test or by measuring voltage. They will look for corrosion, heat damage, and wiring problems. They will check that lamps or LEDs are working and that the fixture is secure.

If the fixture is at the end of its life, they will recommend replacing it, and will explain the options. In some buildings, replacing a few batteries is sensible. In others, with old units and failing parts, replacing the whole fixture is more practical. If the supply is wrong, they will correct it. If the system is central, they will inspect the battery bank, the charger, and the transfer arrangement.

They will explain what is safe, what remains, and whether an interim measure is needed while parts are ordered, such as temporary battery lanterns at exits. They cannot certify that a building meets the fire authority's requirements, which is a matter for the authority and the fire protection contractor. They can make the electrical side work and document what they did.

Three common building types and what goes wrong in each

Retail stores and restaurants often have emergency lights that were installed once and never looked at again. Merchandise is stacked in front of exit signs, a decorative ceiling hides a fixture, or a kitchen's grease and humidity coat the units. Staff may not know where the test button is. In these buildings, a quick walk-through with the manager before opening each day is a practical habit, and an electrician visit can find units that no longer hold a charge.

Offices and clinics tend to have corridors and stairwells with units on the same circuits as the general lighting. When a breaker is turned off for maintenance and never turned back on, the emergency lights go flat. Tenant improvements can also change corridors without updating the lights. In a clinic where patients may need help to move, a dark exit path is a serious concern, and the staff plan should account for how to evacuate in the dark.

Condominiums and apartments have long corridors, stair towers, and often rooftop and garage exits. Water leaks, salt air, and heat all affect fixtures. The association is responsible for most of these units, and managers should keep a log of tests. See condo common area lights and elevator power loss for a related look at how to handle outages in these buildings. Residents should report any dark exit sign right away.

Each building has its own quirks, which is why a technician's site visit matters. They see what the building actually has, not what the drawings say, and can recommend repairs that fit.

A short routine that keeps the system honest

A routine does more than any single repair. Once a month, walk the exits and look at every sign and emergency fixture. Note any that are dark, dim, blinking, loose, or blocked. Press the test button briefly on each fixture that has one, following the manufacturer's instructions, and note whether the lamps come on. Keep a log with dates and initials.

Once a year, or as the fire authority and the manufacturer require, run a longer test that lets the batteries carry the load for the required period. This is best done at a time when the building is empty or when staff can safely work in dim light. Any unit that fails should be repaired or replaced, and the log should show what was done.

Ask the electrician or fire protection contractor what test schedule applies to your building. Do not assume that a standard schedule fits every building. Keep spare batteries or fixtures if the manufacturer recommends it. Train staff so that more than one person knows where the test buttons are and what to look for. When the log shows repeated failures in one area, ask whether moisture, a bad circuit, or a design problem is behind it.

Tenants, owners, and who is responsible

Responsibility for emergency lighting follows the building. In a multi-tenant building, the owner usually maintains the common areas, and the tenant maintains the lighting inside the leased space. Leases vary, and some make tenants responsible for exit signs at the entrance to their suite. Check the lease and ask the property manager. See tenant and landlord power responsibility.

Both parties have an interest in acting quickly. A defect found in an inspection can lead to a notice from the fire authority and, if the building is occupied by the public, to enforcement. An uncorrected defect can also affect insurance if there is a fire. Tell the property manager promptly, in writing, and keep a copy. If you are the owner, do not wait for the next inspection.

If a tenant discovers a failed exit light and the owner does not respond, document it with photographs and dates, and ask the fire authority or the electrician for advice on what to do next. Do not let it drift. Exit lighting is not a nice-to-have feature. It is part of how people get out.

Storms, outages, and testing in South Florida

Hurricane season brings long outages, and emergency lights are designed to last for a limited period. After that, buildings are dark. A business that stays open in a prolonged outage, or a residential building where people remain, must think about alternate light and safe egress. Emergency lighting does not substitute for a generator, and it does not make a dark building safe for occupancy for long.

Before the season starts, test the systems and replace weak batteries. After a storm or a lightning event, test again, because surges can damage chargers and control equipment. Moisture from a roof leak can corrode fixtures. If a storm caused flooding, any emergency lighting equipment that was wet should be inspected.

Keep a supply of flashlights and batteries for staff and a plan for orderly evacuation. If your building has a central system or a generator, ask the electrician and the maintenance contractor how it is tested and what it covers. See hurricane season electrical readiness in Florida.

Calling for help and what to say

When you call, say that it is an occupied building and that exit signs or emergency lights have failed. Describe where, how many, and what you observed. Say whether it began during an outage, a storm, or a test. Say whether the building has normal power now. Mention any smell, heat, or damage. Say whether the public is on site and whether you plan to close.

Say who will meet the technician and who has the keys. Say whether the building is leased and who the owner is. Say if the fire authority has issued a notice. The dispatcher cannot promise an arrival time, but can explain how the visit works and arrange it. Quotes are given by phone. Larger jobs, such as replacing a central system, need an on-site visit, and there is a service call charge, explained before dispatch.

If there is any danger now, call 911 first. If everyone is safe, take the steps above, record what you found, and call. Prompt repair of exit lighting is a simple step that reduces risk for everyone who uses the building.

Questions people ask

Should I close my business if the exit signs are out?

If the building is occupied by the public, consider closing or limiting occupancy until lighting is repaired, and ask the fire authority or a fire protection contractor what applies to you. In the meantime, place flashlights and lanterns at exits and assign staff to guide people. If there is an emergency now, call 911 and evacuate.

Can I replace the battery in an emergency light myself?

Only if you are trained and the manufacturer's instructions allow it. Batteries and chargers are matched, and the wrong battery can overheat the fixture. Fixtures contain energized parts. A technician can test the unit and replace the battery or the entire fixture as needed.

Why does the emergency light work when I press test but fail in an outage?

A short test uses little battery. A real outage runs the lamps for a longer time, and a weak battery cannot sustain them. The battery may also not be fully charged if the circuit feeding the unit is off. A technician can test the unit and the supply.

Who is responsible for exit lights in a leased space?

It depends on the lease and on the location. Owners usually maintain common areas, and tenants may be responsible for fixtures inside the leased space. Ask the property manager and check the lease. Tell the manager promptly, in writing, and keep a copy.

A fixture smells hot or the case is swollen. What should I do?

Do not touch it. A swollen battery or hot casing suggests a battery or charger fault and a possible fire hazard. Keep people away. If there is smoke or a burning smell, call 911. Otherwise, call an electrician and switch off the circuit at the panel only if it is safe and dry.

Does a technician certify that my building meets fire requirements?

No. An electrician can repair and test the electrical side and document what was done. Compliance with fire safety requirements is decided by the fire authority, often with a fire protection contractor. Ask the authority which requirements and records apply to your building, and share them with the technician.

Talk to Emergency Electrician

Reading about "Exit Lights: What to Know and Do"? Tell us what stopped working and when. We will say what an electrician would check first, and quotes are given by phone when the job can be described.

Related pages

  • Common Area Outage: Corridor lights, stairwells, and elevators dark in a condo building? Life-safety steps, who handles what, and what managers should tell residents.
  • Business Power Loss: Your business just lost power. Follow a safe first-hour sequence for owners and managers: safety, isolating the cause, informing staff, and documenting.
  • Tenant and Landlord: Power out at a leased business space? Learn how responsibility is usually divided between tenant and landlord, and why the lease comes first.
  • Continuity Checks: Inspection-style electrical planning for businesses: what a continuity check looks at, how to prepare, and why it reduces surprises without promising results.
  • Season Readiness: A calendar-style plan for South Florida hurricane season electrical readiness: panel, generator, surge, documents and who to call, without promising outcomes.
  • Medical Office: Power failed in a medical or dental office? Learn the life-safety first steps, what circuits and backup planning cover, and what an electrician can do.

Need to discuss an electrical concern or planned project?

Request service
Call (954) 481-0910