Electrical help for homes and businessesRequest service
Emergency ElectricianCall (954) 481-0910
Emergency Electrician electrician at work in a South Florida property

Urgent Repair

Your Business Lost Power: The First Hour

The lights went out, the registers froze, and staff are looking at you. The first hour of a business power loss is about safety, working out whose problem it is, protecting people and equipment, and keeping good records. This page gives owners and managers a calm sequence to follow.

Minute one: people and safety before business

Before anything else, ask whether anyone is in danger. If you see smoke, flames, or sparks, smell burning, hear popping or buzzing from a panel or equipment, or someone has been shocked, call 911 and evacuate the area. Move customers and staff to a safe place outside, away from the building and away from any standing water. Do not go back to check equipment. Fire crews can shut off power and make the building safe, and an electrician can inspect afterward.

If there is no immediate danger, still consider the safety of the people inside. Without power, lights, exit signs, and elevators may fail, and some alarm systems and security doors may behave differently. Emergency lighting is designed to bridge short gaps, but it has limits, and a long outage in a dark building raises the risk of falls. If you cannot keep the space safe and orderly, consider closing temporarily and moving people out.

Some businesses have particular obligations to people who cannot simply walk out, such as customers with mobility problems, patients, or children. Think about them first. If anyone depends on powered medical equipment, call for help immediately. A calm voice and a clear plan help staff stay steady, and they make the rest of the hour easier.

Emergency Electrician dispatch crew meeting beside a branded van in South Florida

Minutes two to ten: is it the whole area, the building, or just you

The first diagnostic question is scope. Look outside. Are the street lights, neighboring businesses, and nearby buildings also dark? If so, the outage is probably on the utility side, and your job is to report it, not to repair it. Call the utility's outage line, or use its reporting tools, and ask about the cause and any estimated restoration information, which may or may not be available. In much of South Florida that utility is FPL, and some cities have municipal systems.

If neighbors have power and you do not, the problem is likely on your side of the meter or at the building's service. Check whether the whole building is dark or only part of it. A partial outage can mean a tripped breaker, a failed phase, a failed sub-panel, or a failure in one of several shared systems. In a multi-tenant building, ask whether other tenants are affected, because that points toward shared equipment owned by the landlord or property manager.

If lights flicker, if some equipment works and other equipment does not, or if some outlets are dead and some are live, note it. Partial or odd behavior is a sign of a failed phase, a loose neutral, or a failing main component. These conditions can damage equipment. Our pages on three-phase loss of phase and loose neutral symptoms explain what they look like. The guide on which problems belong to the utility and which to an electrician helps you decide whom to call.

What a manager can safely look at, and what to leave alone

A manager can safely do a few things. Check whether the main breaker or a branch breaker looks tripped, but do so only if the panel is dry, in a clear area, and quiet and cool, with no burning smell. Notice whether any breaker is in the middle position, which often indicates a trip. Take a photograph of the panel before touching anything. Turn off or unplug sensitive equipment so that a sudden return of power does not surge through it.

Leave several things alone. Do not open panels, remove covers, or touch bus bars. Do not reset a breaker that has tripped repeatedly. Do not attempt to bypass a breaker, jump a connection, or run extension cords from another circuit to power equipment. Do not connect a generator to the building without a proper transfer arrangement. These shortcuts feel productive during an outage, and they are among the most common causes of injuries and equipment damage.

If a breaker has tripped once and the cause is obvious, such as a recently started piece of equipment that overloaded a circuit, a single reset after unplugging the load can be reasonable. If it trips again, stop. Our guide on how to read a tripped breaker explains what different patterns mean, and what never to do in an electrical emergency collects the cautions.

Protecting equipment and inventory

Power loss is a threat to equipment even when nothing is broken. When power returns, surges and voltage irregularities can damage computers, point-of-sale systems, refrigeration compressors, and other electronics. Unplug or switch off sensitive equipment and leave a single light on so that you know when power returns. Wait a few minutes after power is restored before turning equipment back on, to allow the supply to settle.

Think about perishable items. Refrigerators and freezers hold temperature for a limited time if the doors stay closed, but the time depends on the unit and the load, and food safety guidance from health authorities should govern what is kept and what is discarded. Keep the doors closed and avoid opening them unnecessarily. If you operate a food business, see restaurant kitchen power failure and walk-in cooler electrical failure for the specifics.

Think about data and security. Servers and network equipment may need a controlled shutdown if the outage is likely to last. Door locks, alarms, and cameras may run on batteries for a while and then stop. Consider whether the building can be secured, and who has authority to decide to close. For offices with servers, see office server room power problem, and for retail, retail store lighting and register outage.

Telling staff and customers what is happening

Communication is part of the response. Staff need clear instructions: where to go, what to do with customers, which areas to avoid, and who is in charge. A short statement, repeated calmly, is better than a rumor. Tell them that the priority is safety, that you are working out the cause, and that you will update them as soon as you know more.

Customers also need a plain message. If you are closing, say so and explain how they can return or reach you. If you are staying open with limited service, say what is and is not available. Avoid promising a restoration time, because you do not control it. A sign at the door and a message on your phone line or website can reduce confusion and frustration.

If your business serves the public in a regulated setting, such as food service, medical, or childcare, think about what obligations or guidance apply when power is lost, and who must be informed. Look at your own policies and, where relevant, at guidance from the appropriate authorities. This page cannot tell you what applies to your business, but a quick check of your own emergency plan is worth doing before an outage, not during one.

When to call an emergency electrician

Call an electrician when the problem is on your side of the meter, when equipment is damaged, when breakers will not hold, when there are signs of heat or burning, or when you cannot tell whether the building is safe. Call also if the utility has restored service on the street but your building remains dark, since that points to a problem at your service equipment, such as a failed main, a damaged meter base, or a burned panel.

When you call, be ready to describe the building, the nature of the outage, the time it started, and what you have observed. Say whether the whole building or part of it is affected, whether neighbors have power, whether any breaker has tripped, and whether you smell or hear anything unusual. Mention whether the business is food service, medical, or otherwise sensitive to loss of power, because that helps the dispatcher understand the stakes.

Our guide on what to tell the electrician dispatcher and emergency call or next-day visit can help you decide how urgent the situation is. Quotes are given only by phone, complicated commercial jobs need an on-site visit, and there is a service call charge that is explained on the phone before dispatch. A technician cannot promise an arrival time, but the dispatcher can explain how the visit will work.

Different businesses, different priorities

A restaurant will worry about cooking equipment, hoods, and refrigeration, and about food safety timing. A retail store will worry about lights, registers, and security. An office will worry about computers, networks, and phones. A medical or dental office will worry about patient safety and equipment that must keep running. A warehouse or workshop may worry about three-phase equipment and machinery. Each setting has its own first priorities, but the sequence remains: people first, then scope, then protection, then communication.

Tenants have an added layer. If you lease space, find out who owns and maintains the electrical equipment, and who should be called first. A landlord or property manager may be responsible for the building's service and common equipment, while the tenant is responsible for equipment inside the leased space. Our page on tenant and landlord power responsibility describes how this is usually divided, and the lease controls.

Condo associations, HOAs, and commercial parks have their own structures and emergency contacts. If your business is in such a setting, keep those numbers handy. For shared equipment problems, see condo common area outage and HOA and community gate power failure.

Documenting the outage while it is fresh

Start writing things down early. Record the time the power went out, what you saw and heard, what staff reported, who you called, and what you were told. Take photographs of the panel, any visible damage, and the state of the equipment and inventory. Note the temperature readings of refrigeration if you have them. These records help with insurance claims, with discussions with a landlord or utility, and with the technician's diagnosis.

Keep a running list of losses and costs. That includes spoiled inventory, lost sales if you can estimate them from your own records, emergency expenses, and any equipment that failed. Avoid guessing, and write only what you can support. The page on documenting a business outage covers what to capture, and electrical damage and insurance documents covers the insurance side.

Ask the technician for a written findings report describing what was found and what was done. See getting a written findings report. This is useful for your own records and for any party that needs to understand the cause.

After the first hour: restoring power safely and planning ahead

When power returns, restore equipment gradually. Turn on main circuits first, then essential systems, then individual equipment, one at a time, watching for signs of trouble. If a breaker trips, a smell appears, or equipment behaves strangely, stop and call. Do not push through an irregularity to get open. A short delay is better than damaged equipment or a hazard in a building full of customers.

After the event, review what happened. Was the cause the utility, the building, or your equipment? Did your staff know what to do? Did the emergency lighting work? Were the right numbers available? Did the equipment survive? That review is the beginning of a continuity plan. See preventive checks for continuity and backup power for small business for ideas.

No one can promise that a business will never lose power. What preparation can do is reduce the confusion and the damage when it happens. If your business is dark right now and you are not sure why, call, describe what you see, and let a technician help decide the safest next step.

Questions people ask

How do I tell whether the outage is the utility's problem or mine?

Look outside. If street lights and neighboring buildings are dark, the cause is probably on the utility side, so report it to the utility. If neighbors have power and you do not, or if only part of your building is out, the problem is likely on your side of the meter. Odd behavior such as flickering or half-dead outlets should be reported to an electrician.

Is it safe to reset the breaker myself?

Once, with the load unplugged, if the panel is dry, accessible, and without burning smells or noise, and the cause seems obvious. If it trips again, stop and call. Repeated trips indicate a real fault, and forcing a breaker can cause overheating or fire. Do not open panels or bypass protective devices.

Can I run a generator to keep the business open?

Only with a correct setup. A generator should never be connected to building wiring without a proper transfer arrangement, because backfeed can endanger utility workers and damage equipment. Generators must be used outdoors, away from doors and windows, because of carbon monoxide. Ask an electrician about a safe arrangement rather than improvising during an outage.

Should I close the business or stay open without power?

That depends on safety. Without lighting, exit signs, alarms, or ventilation, a building can become hazardous, and some business types have specific obligations. If you cannot keep people safe and the space orderly, closing is the cautious choice. Check your own emergency plan and any guidance that applies to your type of business.

What should I write down during the outage?

Record the time the power failed, what you saw, heard, and smelled, who you called and what they said, the condition of equipment and inventory, and any temperature readings. Take photographs before anything is moved. These notes support insurance claims, discussions with landlords or utilities, and the technician's diagnosis.

How do quotes and the service call charge work for a business?

Quotes are given only by phone. Commercial power problems usually need an on-site visit, and there is a service call charge that is explained on the phone before dispatch. Call, describe the building, the outage, and what you have observed, and the dispatcher will explain the process. No arrival time can be promised.

Talk to Emergency Electrician

Reading about "Your Business Lost Power: The First Hour"? Tell us what stopped working and when. We will say what an electrician would check first, and quotes are given by phone when the job can be described.

Related pages

  • Restaurant Kitchen: When a restaurant kitchen loses power, hood, walk-in and line equipment circuits all matter, and so does food safety timing. See safe steps and what to tell us.
  • Loss of Phase: One phase dropped in a three-phase business? Learn the warning signs, which motors to shut down, who to tell, and what is checked.
  • Outage Records: What to record during a business power outage for managers, landlords and insurers: timelines, photos, losses and technician findings, with no coverage claims.
  • Server Room Power: Server closet or small office rack lost power or keeps tripping? Learn the safe first steps, what an electrician checks, and what to tell the dispatcher.
  • Condo Emergency: Board members and managers: a call order for condo electrical emergencies, who handles shared rooms, what residents report, and what to document afterward.
  • Common Area Outage: Corridor lights, stairwells, and elevators dark in a condo building? Life-safety steps, who handles what, and what managers should tell residents.

A short script for whoever answers the phone

When power fails, the person nearest the front counter usually becomes the voice of the business, so it helps to decide ahead of time what that person says. A plain script works best: the lights are out, we are checking the cause, here is what we can still do, and here is how we will update you. Keep it honest and without guesses about how long things will take, because a wrong estimate creates more frustration than no estimate at all. Write the script on a card near the register or the office phone so that a new employee on a busy shift can read it without having to improvise under pressure.

Include a few lines for vendors and delivery drivers too. A produce truck arriving during an outage needs a clear answer about where to unload and whether the cooler can receive product safely. A contractor arriving for a different job should be told that electrical work areas may be restricted. Decide who holds the keys to the electrical room, who may open the panel door, and who must never do either. Writing these decisions down while the building is calm saves several minutes of confusion when it is dark, hot and loud, and it keeps well-meaning staff from taking risks near equipment they do not understand.

Finally, give the script a second half for the call to an electrician. Note the business name, the address, the nature of the outage, what you saw or smelled, what is still working and what has been switched off. Call us and describe the situation plainly, and we will explain what the scope of work is likely to involve and confirm availability before anything begins. Having these facts ready on one page means the conversation is short and useful, and it lets the technician arrive with a better idea of which tools and parts to bring.

Need to discuss an electrical concern or planned project?

Request service
Call (954) 481-0910