Electrical help for homes and businessesRequest service
Emergency ElectricianCall (954) 481-0910
Emergency Electrician technicians reviewing a work order beside a branded van at a South Florida home

Electrical service

Emergency Electrician for Broward County and South Florida

Sparks, a burning smell, a dead panel or power that will not come back? This site helps you reach an emergency electrician in Broward County and nearby South Florida cities, explains what to do first, and shows what an urgent electrical visit involves. If you see flames or someone is hurt, call 911 first, then call for repair once everyone is safe.

Safety first: when 911 comes before any electrician

An electrician is the right call for most electrical trouble, but not the first call for every situation. If you can see flames, if smoke is coming from a wall, an outlet, a panel or an appliance, or if someone has been shocked and is hurt, confused or not responding, call 911 first. Get everyone out of the building, stay out, and let the fire department decide when it is safe to go back in. An electrician cannot help while the building is burning, and no repair is worth a delay in reaching emergency responders.

The same applies if you smell something burning and cannot find the source. Our burning smell call order guide lays out the sequence, and the page on a burning smell with no visible fire explains why hidden heat inside a wall is treated as serious. If a small flame is already visible, read what to know about small electrical fires before anything else, and remember that water is not the answer to an electrical fire.

  • Flames, or smoke coming from a wall, outlet, panel, fixture or appliance: leave and call 911.
  • A person who has been shocked and is hurt, dizzy, burned or unresponsive: call 911, do not touch them if they may still be in contact with the source.
  • A downed or sagging wire outside: stay far back, keep others away, call 911 and the power company.
  • A carbon monoxide alarm sounding while a generator or fuel appliance runs: get into fresh air and call 911.

The utility and the electrician are different calls

Many callers do not know which side of the meter a problem sits on. The power company is responsible for the lines in the street, the equipment on the pole, and the service wires running to your building up to the point where they connect. The electrician is responsible for what belongs to the property: the equipment at and after the connection point, the panel, the wiring, the outlets and the fixtures. The guide on who fixes what draws that line in plain terms, and the disconnect and reconnect process explains why some repairs require the utility to cut and restore power around the work.

Emergency Electrician technician using an infrared camera to inspect a residential electrical panel

A wire down in the yard is the clearest example. Treat every fallen line as live, even if it is not sparking or humming. Our page on a downed wire in the yard and the page on a line touching a tree or fence explain why distance matters and why a wet lawn makes everything worse. You call 911 and the utility. The electrician comes later, after the utility has made the line safe, to repair whatever is on the property side.

If only your building is dark while the neighbors still have lights, the cause is probably on your side of the connection. That case is covered in only your house is dark, and it is a typical reason to call an electrician rather than wait for the utility.

What to tell a 911 dispatcher

A dispatcher asks short questions in a set order, and the calmer and clearer your answers, the faster help is sent. Give the address first, including the unit or building number if you are in a condo or apartment complex. Then say what you see: smoke, flames, a person injured, a wire down, water around electrical equipment. Say whether anyone is still inside and whether you are somewhere safe. Stay on the line until the dispatcher says you can hang up.

Do not go back for belongings, pets or papers. Do not stop to switch off breakers if that means walking past smoke or standing in water. If you have already left the building and the main breaker is dry, easy to reach and not near any smoke, the dispatcher may tell you what to do; follow the instructions you are given on the call rather than a web page. The full script, with sample wording for different situations, is in what to tell the 911 dispatcher.

Afterward, the fire crew may leave a note, shut off power at the meter, or tag the building. That matters for what happens next, and we cover it in after the fire crew leaves. In short, the building may need an electrician to inspect and repair before power is restored, and the utility may need to reconnect once the work is done.

Water and electricity: the combination to respect

Water in the wrong place turns a repair problem into a safety problem. Water in or on an electrical panel, water dripping from a light fixture, a flooded outlet, or standing water around equipment all call for distance. Do not stand in water to reach a panel, do not touch switches or breakers with wet hands, and do not try to dry out electrical equipment while it is energized. The basics are in wet hands, wet floors and electricity.

The specific cases are covered separately because each one is handled differently. Water in the electrical panel is a different situation from water in an outlet or switch, and both differ from flooded outlets after a water intrusion. A less obvious one is a mild tingle when touching a faucet or pipe; a shock from a faucet or pipe can point to a fault in the building, and it should never be ignored or tested by touching again.

If water is rising or has already reached outlets, leave the main breaker alone unless you can reach it from dry ground, and tell the dispatcher or the electrician exactly what is wet. Equipment that has been under water is not something to switch back on to see if it works. A technician has to inspect it, and some of it will need replacing.

Warning signs that justify an urgent call

Not every electrical problem is an emergency, and calling it one wastes time you may need. But some signs are strong enough that waiting is the wrong choice. Sparks from an outlet, a plug that has melted into the socket, a panel door that is hot to the touch, buzzing from a breaker box, a breaker that will not stay reset, or a wall that feels warm all point to heat or arcing inside the system. Heat is how electrical fires begin, and these are the early stage.

Each of these has its own explanation. Read about sparks from an outlet, a melted plug, a hot breaker or panel door, buzzing from the panel, a breaker that will not reset, and a wall that is warm to the touch. Smoke from the panel itself is covered on its own page: smoke from the panel is a 911 situation first.

If you are not sure whether your situation qualifies, the decision pages are meant for that moment. The emergency decision chart and emergency call or next-day visit walk through the questions an experienced dispatcher would ask, so you can decide how urgently to act. When in doubt, shut off what is safe to shut off, stay away from the affected area and call.

Storm, flood and lightning across South Florida

South Florida homes face a long hurricane season, heavy summer thunderstorms, flooding from rain and surge, and salt air along the coast. Each of these puts stress on the electrical system in a different way. Preparation helps: the pre-storm electrical checklist and the page on when to shut off the main before a storm explain what is reasonable to do ahead of time and what is not.

After floodwater recedes, the wiring behind walls and the equipment low to the floor are the concern. First steps in a flooded home explains what to leave alone, what floodwater does to wiring covers why damage can be hidden, and saltwater surge damage explains why salt is especially hard on metal and connections near the coast.

Lightning is a separate story. A direct hit can damage wiring and start hidden damage, while a nearby strike can quietly ruin electronics. Read lightning strike house damage and nearby lightning and electronics. Trees are another frequent cause of calls: a tree on the house and a tree on the service line both involve damage the utility may need to address first. The full set of guides is collected in the storm and flood section.

Power returning after an outage: the quiet hazard

Restoration brings its own risks. When the utility restores power after a storm, the surge of returning current can trip breakers, damage appliances, or expose a fault that was waiting for a reason to show itself. If you left a generator wired in a way that could feed power back toward the lines, that is a danger to the crews working outside as well. The page on backfeed danger explains it clearly, and generator safety after a hurricane covers placement, fuel and carbon monoxide.

If the main breaker will not stay on after a storm, or breakers keep tripping once power is back, do not keep forcing it. Read main breaker will not stay on and breaker trips after power returns. The same goes for after-storm power restoration safety, which lists what to check before turning anything back on.

A small number of homes lose only part of their power, with half of the house dark or one room dead. Those cases usually point to a failure inside the panel or on one circuit rather than a utility problem, and they are discussed in half the house has no power and one room with no power.

What urgent repair covers

Once the immediate danger has passed, the repair work falls into a few familiar categories. A failed breaker or panel may need urgent breaker replacement or urgent panel replacement. A damaged outlet or switch needs urgent outlet repair or switch and dimmer repair. Problems at the service connection involve the service mast, the meter base or a service upgrade.

When the cause is not obvious, the work starts with finding it. An urgent troubleshooting visit is a diagnostic visit, and tools like ground fault tracing and short circuit location are how a technician narrows down a hidden fault. Burned or damaged wiring is handled through wire repair and splicing or burned wiring replacement. When the power has to come back before a full repair can be done, there is temporary power restoration, which is explained separately because a temporary arrangement is not a finished repair.

Businesses, condominiums and associations have their own needs. See the business power loss checklist and condo association electrical emergency, or browse everything in the urgent repair section.

How an emergency electrician call actually works

Here is the sequence, so nothing about the call is a surprise. You call the number on this site and describe what is happening in plain words: what you saw, smelled or heard, whether anything is wet, and whether you have already contacted 911 or the utility. If the situation sounds like a fire or shock emergency, the person on the phone will tell you to get emergency responders first. Otherwise, they will ask the questions needed to understand the problem and decide whether a visit makes sense.

Quotes are given by phone only, and only after the problem is understood. Straightforward repairs can often be described on the call. Complicated jobs need an on-site visit before a number can be given, and an on-site visit carries a service call charge. That charge is explained on the phone before anyone is dispatched, so you decide with the information in front of you. We do not publish prices on the website, and we do not promise arrival times, because traffic, weather, and the number of calls in progress change what is realistic.

A few preparation tips help the call go faster. The page on what to tell the electrician dispatcher lists what to have ready, the guide on questions to ask before dispatch lists the questions that are worth asking, and what to expect when the technician arrives describes the visit itself. If you are choosing between companies under pressure, how to choose an electrical contractor in a crisis is worth a few minutes, including advice on verifying credentials yourself.

Where we cover: Broward County and the cities from Boca Raton to North Miami

This service is organized around the stretch from Boca Raton to North Miami, and the city pages are written with the local housing in mind rather than swapped names. Older masonry homes near the coast, newer planned communities further west, high-rise condominiums, shopping plazas and warehouse districts all create different kinds of calls. In Broward, see Fort Lauderdale, Hollywood, Pembroke Pines and Coral Springs. At the northern end, see Boca Raton. At the southern end, see North Miami.

Every city has its own permit office and its own inspection practices, and some emergency work needs a permit even when it is urgent. Read whether you need a permit for emergency electrical work for the general picture, and ask the person on the phone how it applies where you live. The service areas section lists every city page.

Coverage is a statement about the region, not a promise of a technician at a certain hour in a certain place. When you call, you will hear what is realistic for your location on that day.

Records, prevention and the next call you hope never to make

After the emergency, a few habits protect you. Take pictures before anything is repaired: photographing the damage before repairs explains how, and electrical damage and insurance documents describes what an insurer is likely to ask for. A written findings report from the technician helps too, and getting a written findings report lists what it should include. For a business, documenting a business outage serves the same purpose.

Prevention starts with knowing your own system. Find your main breaker before you need it, and label your panel so anyone can follow it in the dark. Learn the warning signs that come before an outage and read what never to do in an electrical emergency. For a household plan, see the household emergency plan for power loss, and for after the repair, preventing a repeat electrical emergency.

All of these live in the safety and guides section, and the emergencies section collects every triage page in one place. If your situation is stable and safe, and you want a qualified person to look at it, call and describe it. A person on the phone will walk through what is happening, explain how the visit and the service call charge work, and tell you what the next step looks like.

Questions people ask

Should I call 911 or an electrician first?

Call 911 first if you see flames, if smoke is coming from a wall, outlet, panel or appliance, if someone has been shocked and is hurt, or if a power line is down. An electrician repairs the problem after the danger has been handled. If you are unsure, call 911 and describe what you see, then call for repair once everyone is safe.

Who do I call when a power line is down outside?

Stay far away, keep other people and pets away, and call 911 and the power company. Treat every fallen line as live even if it is quiet. An electrician gets involved afterward, once the utility has made the line safe, to repair damage on the property side such as the mast, the meter base or the wiring.

How does pricing work for an emergency electrical call?

Quotes are given only by phone. Simple repairs can often be described on the call after the problem is understood. Complicated jobs need an on-site visit first, and that visit carries a service call charge. The charge is explained on the phone before anyone is dispatched, so you can decide before a technician leaves.

How soon will a technician arrive?

We do not promise arrival times. Traffic, weather, storm conditions and the number of urgent calls in progress all change what is realistic. When you call, you will be told what to expect for your location that day, and you can decide whether to wait or contact someone else. If there is any danger, contact 911 rather than waiting.

Is it safe to reset a tripped breaker myself?

Sometimes, but not when there was smoke, a burning smell, sparks, water, or a breaker that trips again right away. A breaker that will not stay on is telling you there is a fault. Do not keep forcing it. Our guides explain how to read a tripped breaker and when to stop and call.

Which areas do you cover?

The site is organized around Broward County and the cities from Boca Raton to North Miami, with city pages for many communities. Coverage describes the region, not a promise of a technician in every place at every hour. When you call, give the address and you will be told whether and how the visit can be arranged.

Talk to Emergency Electrician

Reading about "Electrical Emergency? Start With Triage, Then Call for Repair"? Tell us what stopped working and when. We will say what an electrician would check first, and quotes are given by phone when the job can be described.

Related pages

  • 911 Script: Calling 911 about sparks, smoke, a shock or a downed wire? These are the facts that help dispatch most: address, hazard, people at risk and power status.
  • Emergency Check: A branching guide from symptoms to urgency, showing when to call 911, when to call the utility, when to call an electrician now, and when a visit can wait.
  • Downed Wire: A wire on the ground may be live even if it is silent. Learn how to keep a safe distance, call 911 and the utility, and what never to do near a fallen line.
  • Flood First Steps: What to do about electricity in a flooded home: stay out of water near power, how the utility disconnect works and why inspection comes before power returns.
  • Troubleshooting Visit: A walkthrough of an urgent electrical troubleshooting visit: arrival, safety isolation, testing, findings explained in writing, and how phone quotes work.
  • Panel Buzzing: Some panel hum is normal, but loud buzzing can signal arcing or a loose connection. Learn to sort the sounds and what to tell the dispatcher about them.

Emergency electrician by city

Choose your city to see local notes and common urgent electrical problems.

Need to discuss an electrical concern or planned project?

Request service
Call (954) 481-0910