Who owns what: the dividing line at the meter
The simplest way to understand a disconnect is to start with ownership. The utility owns its wires, its transformers and, in most cases, the meter. You, as the property owner, own the equipment on your side of the service point, which usually includes the service mast or entrance conduit, the meter base or socket, the main disconnect and the panel. In the Florida region this is a familiar split, but the exact boundary depends on whether the service is overhead or underground and on the utility's own rules.
That boundary matters because different parties are allowed to work on different parts. A qualified electrical contractor works on the customer's equipment. The utility works on its own equipment and controls the meter. A contractor should not cut the utility's seals or touch its conductors, and a utility will not repair a customer's panel. When a repair crosses the boundary, such as a damaged mast that carries the utility's wires, both sides are involved, in a particular order.
If you are unsure which side a failure is on, call 911 first if there is any danger, then the utility if wires are down or the problem looks like it is outside your property, and a qualified electrical contractor if the problem looks like it is in your equipment. The guide on who fixes what, the utility or the electrician goes through examples.

Why a service gets disconnected in the first place
Several situations lead to a disconnect. The most common reason is that the equipment at the service point must be replaced or repaired and cannot be worked on while energized. A leaning or torn mast, a damaged meter socket, a burned main panel or a damaged service cable all require the utility to cut power, or to pull the meter, before the contractor can work safely.
Disconnects also happen after fires, floods and storms, when the fire department, the utility or an inspector decides that an unsafe building should not be energized. In some cases, a disconnect is ordered because of a hazard found during an inspection, such as exposed live parts or evidence of tampering. A utility may also disconnect for reasons related to the account, which is a separate matter that has nothing to do with the electrical condition of the building.
Whatever the reason, the principle is the same: the disconnect protects people. It is not a punishment, and it is not something that can be skipped by making the repair quickly.
The usual sequence when a service is pulled for repair
The details vary, but a typical sequence looks like this. Read it as a general outline, not a schedule. Each step has its own people and its own timing, and nobody controls all of them.
- A hazard or failure is identified, and anyone in danger is moved to safety. Emergency services are called if needed.
- A qualified electrical contractor assesses the damage and explains what needs to be repaired or replaced, and whether the utility must disconnect or pull the meter.
- The contractor, and sometimes the customer, contacts the utility to request the disconnect for the work. In an emergency, the utility may act on its own priorities and schedule.
- The utility disconnects service at the pole, the transformer or the meter, depending on the situation.
- The contractor makes the repairs, usually under a permit with the local building department.
- The contractor requests an inspection. An inspector reviews the work and, if it is acceptable, signs off.
- The utility is told that the work has passed, and it schedules the reconnection, which may include reinstalling the meter.
- Power is restored, and the contractor or the customer checks that the building is operating normally.
Permits and inspections in the middle of the process
Work at the service point typically requires a permit, since it involves the equipment that connects the building to the grid. The contractor applies for it and later requests an inspection. The inspector checks the finished work against the applicable electrical rules, and the result is recorded. For a general view of how this works, see permits for emergency electrical work.
A common source of frustration is the gap between the repair being finished and the power coming back. The contractor may be done, the equipment may be tested, and yet the utility is waiting for the inspection result, or the inspection is waiting for an appointment. These steps are handled by different organizations with different schedules, and a good technician will tell you honestly what is pending instead of guessing at a time.
Ask the contractor to describe, in plain words, which step you are waiting on and who is responsible for it. Writing that down helps you follow up with the right party.
What an inspector looks at for a service repair
For a service repair, an inspector commonly looks at things that affect safety at the point of connection. They check that the mast or conduit is secure and properly supported, that the weatherhead or entrance fitting keeps water out, that the meter base is properly mounted and rated, that the main disconnect and the panel are the right type for the service, and that grounding and bonding connections are made as required.
They also look at labeling, clearances and access. The panel should have working space in front of it, clear of storage and obstructions. The meter should be reachable by the utility. Outdoor equipment should be rated for the environment, which in South Florida means moisture, salt air and wind-driven rain. The guide on storm-damaged meters and masts explains how those parts fail after a hurricane or a tropical storm.
If the inspector finds something that does not meet the applicable rules, the contractor corrects it and requests another inspection. Clear access and a visible address number help the inspector, so make sure gates are unlocked, pets are secured and the equipment is reachable.
What the utility needs before it reconnects
Each utility has its own requirements, and they can change, so this is a general description. In many cases, the utility needs evidence that the repair was approved by the local authority, along with a request to reconnect from the contractor or the customer. The utility may also need to confirm that the account is active and that the equipment on its side is ready.
Some utilities handle the meter reinstallation and the energizing of the service in a single visit, and some need separate steps. The utility decides when its crews can come, based on its own workload, especially after storms when many customers are waiting. No contractor can promise an arrival time for utility crews, and a dispatcher cannot either.
Ask your contractor to tell you which reference numbers or permit numbers will be needed, and write them down. If you speak to the utility yourself, note the date, the name of the person you spoke to and any confirmation number they give you.
Temporary power and why it is not an informal matter
During a long wait, it is natural to ask whether some power can be restored temporarily. In some situations, a temporary service can be arranged for specific purposes, with approvals from the inspector and the utility. This is a formal process that involves its own equipment and its own sign-off. It is not something to arrange by reconnecting wires or bypassing a pulled meter.
Never reconnect a service yourself, never bridge a meter socket and never ask a friend or neighbor to do it. These actions put the person doing them and anyone nearby at risk, and they can cause damage that makes the eventual repair more complicated. If a contractor offers to do this for you, ask whether it has been approved by the inspector and the utility, and ask for that in writing.
For information about how temporary power is handled on the repair side, see urgent temporary power restoration. Even then, the approvals described above remain.
Preparing your property for the visits
Several people may need to reach your equipment during this process: the contractor, the inspector and the utility crew. A little preparation prevents wasted visits. Make sure the meter and the panel are reachable, that gates are unlocked or that someone can open them, that dogs are secured, and that nothing is stacked in front of the equipment. A visible, legible address number on the building or the meter helps crews find the right place, especially at night or in a storm.
If the panel is inside a closet, a garage or a utility room, clear a path and the working space in front of it. If the meter is behind a fence or in a side yard with overgrown plants, trim back what you can safely reach, without touching any wires. In a condominium or a managed community, find out who holds the keys to electrical rooms and meter rooms and ask them to be available, since a locked door can delay an inspection by days.
Keep your phone nearby and answer calls from unfamiliar numbers during the process, since the utility, the inspector and the contractor may all call to confirm access. If you rent, tell the owner or manager when visits are scheduled, so that someone with authority can let people in if you are not home. Keep a short log of each visit with the date and the name of the person who came, which makes it easy to follow up if something is missed.
Generators during the wait
If you use a portable generator while waiting, keep it outdoors and well away from windows, doors and vents, because the exhaust contains carbon monoxide that can kill. Connect appliances directly to the generator with suitable cords, and never plug the generator into a wall outlet to power the building. This practice, called backfeeding, can send electricity out to the utility's lines and seriously harm line workers, and it can damage your own equipment.
A properly installed transfer switch or an interlock device separates the building from the utility and allows a generator to power selected circuits. Installing one is electrical work that normally requires a permit and an inspection, and it is not a job to be done in a hurry in the middle of an outage. The guide on generator inlets and transfer switch basics explains how these are set up.
If you depend on electrically powered medical equipment, tell the utility and your medical provider right away, and make a plan that does not rely on a rushed installation. The guide on extended outages, food and medical power covers planning in more detail.
After power returns
When service is restored, do not switch everything on at once. Turn on the main breaker, then the individual breakers one at a time, and watch for anything unusual: a breaker that trips, a smell, a buzzing, a light that flickers or equipment that behaves strangely. If something is wrong, turn it off and call. For hazards such as smoke or sparks, call 911.
Surges can occur when power returns, so keep sensitive electronics unplugged until things have settled. Turn on large loads such as the air conditioner gradually, and give the system a short time between steps. If you see signs of trouble on one circuit, leave it off and have it checked.
Keep your records of the process: dates, reference numbers, the permit and the inspection result. The guide on documents that help after electrical damage lists what to keep. If you need a qualified electrician to assess equipment at the service point, or to prepare for a disconnect and reconnect, call and explain what you see. The dispatcher can explain the service call charge before anyone is sent, and can tell you whether the situation looks like it needs an on-site visit before a quote.
Questions people ask
Who contacts the utility to schedule the disconnect?
It varies. Often the electrical contractor contacts the utility on your behalf, since they know what information is needed. In some cases the customer must make the request or confirm it. Ask the contractor who will call, which account details are required and what reference number you should note, so that you can follow up.
Why is my power still off after the repair is finished?
Because the repair, the inspection and the utility's reconnection are separate steps handled by different parties. The work may be complete while an inspection is pending or the utility is waiting to schedule a visit. Ask the contractor which step is outstanding, and keep notes of dates and reference numbers.
Can the electrician restore power themselves?
A contractor can repair the customer's equipment, but the utility controls its own wires and the meter. The utility normally reconnects service, often after receiving evidence of an approved inspection. A contractor who offers to bypass the utility or reconnect a pulled meter is suggesting something unsafe and should be declined.
Is a disconnect always needed for a panel replacement?
Usually the service must be de-energized for the work, and depending on the equipment and the utility, that may mean a utility disconnect or meter pull. The technician can explain what is needed in your case after assessing the equipment. It is a good question to ask on the phone before any visit is scheduled.
Can I use a generator while waiting for reconnection?
Yes, if used safely: outdoors, away from openings, with cords running directly to appliances, and never connected to a wall outlet or panel. A properly installed transfer switch or interlock is a different matter and needs a permit. Never run a generator indoors or in a garage, since carbon monoxide is deadly.
What should I do first when power comes back?
Turn the main breaker on, then individual breakers one at a time, and watch and smell for anything unusual. Keep sensitive electronics unplugged until things settle, and bring large loads online gradually. If a breaker trips, there is a burning smell, or anything buzzes or sparks, turn it off. Call 911 for smoke or fire.
Reading about "Utility Disconnect and Reconnect Explained"? Tell us what stopped working and when. We will say what an electrician would check first, and quotes are given by phone when the job can be described.
Related pages
- Emergency Permits: How urgent electrical repairs still move through permits and inspections in South Florida, what usually needs one, and what to ask before work starts.
- Who Fixes What: Where utility equipment ends and customer equipment begins, in general terms, so you know whether to call the power company, an electrician, or 911 first.
- Temporary Power: When a full electrical repair has to wait, isolating the damaged part can keep the rest of the home running. Learn how temporary power is done and its limits.
- After-Storm Power: What to check before the utility re-energizes your service after a storm, what to leave off, and how to bring a house back online without damage or hazards.
- Call Order: Electrical trouble, three possible calls. A plain decision order for when to dial 911, when to phone the power company, and when to call an electrician.
- Emergency Check: A branching guide from symptoms to urgency, showing when to call 911, when to call the utility, when to call an electrician now, and when a visit can wait.
