Safety first: people, then property
Before thinking about equipment, think about people. If there is smoke, fire, a strong burning smell, sparking, a person who has been shocked or any downed wire, call 911, get everyone out and stay out. Appliances can be replaced. Nothing in this guide is a reason to stay near a hazard or to touch wet or damaged equipment.
If the area is wet, do not walk through standing water to reach plugs, power strips or appliances. Water that touches energized parts can make the surrounding area dangerous. Wait until the power has been shut off safely and the area has been checked by a qualified person. If you cannot tell whether the area is safe, treat it as unsafe.
Once the situation is calm and you can reach your devices without risk, the steps below help you protect the equipment that is worth protecting and avoid making damage worse.

Why electrical events damage equipment in different ways
Not all events harm devices in the same way. A power surge, which is a brief jump in voltage, can overstress the electronics inside a device and cause immediate failure or weaken components so that they fail later. A lightning strike nearby can induce a surge in wiring even without hitting the home. An outage followed by a restoration can produce short spikes as power returns. A loose neutral or a utility-side problem can cause some circuits to run at too high or too low a voltage, which is harmful to motors and electronics.
Water and smoke cause other types of harm. Water can short circuit boards and corrode connectors, sometimes days after the event. Smoke carries soot and acidic residue that settles into vents and circuit boards. Heat can warp plastic and damage insulation. Even equipment that looks clean may have residue inside.
Because of these differences, the right response depends on what happened. A device that was plugged in during a nearby lightning strike deserves a different approach from one that was submerged. The guide on surge, spike and outage terms explains the vocabulary.
The first step: unplug before you power anything
After any event involving a surge, water, fire or strange electrical behavior, the first rule is to unplug devices before power is restored or before you try them. Doing this protects them from a second surge when the power returns and prevents you from energizing something that has been damaged. If power is already on, unplug devices only if you can reach the plug without stepping through water and without touching anything damaged.
Unplug from the wall, not from the device, and pull on the plug, not the cord. For power strips and surge protectors that have been in a surge or in water, do not reuse them. The protective parts inside may have been used up, and the strip may be unsafe. Keep them aside for disposal in line with local rules.
Leave the appliances unplugged until a qualified person has checked the circuits that feed them. If the circuit itself was damaged, plugging in an appliance can create a new hazard. The technician can tell you when it is reasonable to plug things back in.
Triage: sorting what you have
It helps to sort your belongings into groups, so you can decide what to do about each. The groups below are a general guide. Use judgment, and when in doubt, treat the device as unsafe until it has been checked.
Take photographs and make a list as you go. The guide on photographing electrical damage before repairs explains how to document without taking risks.
- Items that were exposed to water, even briefly: keep off, unplugged and set aside for evaluation or replacement
- Items that were exposed to smoke or soot: keep off and unplugged, since residue can damage them when powered
- Items that were plugged in during a surge or a nearby lightning strike and show no visible damage: keep unplugged until the circuits are checked, then test one at a time
- Items with visible scorching, melting or odors: do not use, and keep them away from combustible materials
- Items that were not plugged in and were not exposed to water or smoke: usually fine, but plug them in only after the circuits are confirmed safe
- Large appliances that are hard-wired or on dedicated circuits, such as ranges, dryers, water heaters and air handlers: leave for a qualified technician to check
Testing devices that seem fine
After the circuits have been checked and declared safe, you may want to try your devices. Do it gradually. Plug in one device at a time, and watch and smell for anything unusual: a burning smell, smoke, sparks, a hum, a hot plug or a hot cord. If something seems wrong, unplug it immediately and leave it off.
Be especially cautious with devices that contain batteries, such as laptops, power tools and phones. Damaged batteries can overheat. If a device or its charger is swollen, hot, discolored or smells unusual, stop using it and keep it on a non-flammable surface away from other items.
Remember that a device that powers up is not necessarily undamaged. Electronics can fail days or weeks after an event. If you notice odd behavior later, such as random restarts, flickering displays, corrupted data or unusual noises, stop using the device and have it checked. Keep your records so that you can explain the sequence of events.
Refrigerators, cold storage and other critical appliances
Refrigerators and chest coolers are a particular concern because they hold food and sometimes medication. If the power has been out, keep the doors closed as much as possible to hold the cold. When power returns, give the appliance a little time before you check it, and listen for normal sounds. A compressor that hums without starting, clicks repeatedly or runs hot may have been damaged by the surge or by low voltage.
Food safety is a separate question from electrical safety, and local health guidance applies. If you are unsure whether food has stayed cold enough, the safest practice is to follow official food safety guidance and discard what you cannot trust. Medication that requires refrigeration should be discussed with a pharmacist or a doctor.
If a refrigerator was in a flooded area, do not plug it in. Water in the compressor and the wiring can create a shock hazard. The guide on extended outages, food and medical power offers planning advice for long outages.
Air conditioners, pool equipment and outdoor units
In South Florida, the air conditioner is often the largest electrical load and the most expensive appliance affected by surges and storms. If the outdoor unit or the air handler was exposed to a surge, flood water or a nearby strike, do not keep trying to start it. Repeated start attempts can damage a compressor that is already struggling. Turn the thermostat to off and leave the system off until a qualified technician checks the disconnect, the wiring and the unit.
Pool pumps, heaters, lights and salt systems are exposed to weather and water, and they sit on circuits with added protection. If they tripped a breaker or were exposed to a flood, leave them off. Pool electrical problems can create shock hazards in the water. The guide on pool and spa electrical after a flood explains why this deserves care.
For outdoor equipment, check from a distance whether the enclosures are intact and dry, and leave the closer inspection to a technician. An HVAC technician and an electrician may both be needed, since the electrical supply and the equipment are different parts of the problem.
Computers, data and small electronics
For computers and storage devices, the value is often in the data. If a computer was exposed to water or smoke, avoid turning it on. Powering up wet or contaminated electronics can destroy data that might otherwise be recoverable. A data recovery professional can advise on options. If the device was only exposed to a surge and appears normal, copy important files to another location as soon as it is safe to power it on.
For televisions, routers, game consoles and similar items, check for visible damage first. If a surge hit and nothing turns on, try a different outlet on a circuit that has been verified, since the original circuit may be at fault. Do not open the casing of an electronic device or a power supply, because they can hold a charge even when unplugged.
Smoke alarms and carbon monoxide alarms count as critical electronics. If they were exposed to a surge or fire, ask the technician to check their wiring and replace any that look suspect. Do not leave the home without working alarms.
Kitchen and laundry appliances on their own circuits
Ranges, ovens, dryers, dishwashers and disposals often sit on dedicated circuits, and the wiring and receptacles for them are heavier than ordinary outlets. If one of these appliances was involved in an event, such as a dryer plug that melted, a range outlet that sparked or a dishwasher that tripped a breaker, do not keep using it. The problem may be in the appliance, the cord, the receptacle or the circuit, and only a technician can sort out which.
Look, without touching, at the plug and the outlet for discoloration, melting or a burning smell. Photograph what you see. Pull the appliance out only if it is cool, the circuit has been turned off and you can do so without force. A plug that is fused to an outlet should be left for the technician. The guide on what to do when a stove or dryer outlet sparked goes into the details.
Because these appliances draw a lot of current for long periods, a loose connection at the plug or the terminals tends to heat up. That makes the cause of an appliance failure on a dedicated circuit worth examining, not just the appliance. Ask the technician to check the receptacle, the cord and the breaker as a set.
Deciding between repair, replacement and a second opinion
Whether to repair or replace an appliance depends on its age, its value, the extent of the damage and the cost of repair, which a service professional can estimate for the specific item. Ask a qualified appliance technician or the manufacturer for guidance on items that matter to you. A technician who evaluates an appliance should also tell you if the damage appears related to the electrical supply, since fixing the appliance without fixing the cause may lead to a repeat.
That is where an electrician comes in. If more than one device failed, or if the failures cluster on one circuit or after one event, ask an electrician to check the circuits, the panel and the service for the cause. Surge protection, a failing neutral connection or a utility-side issue may be involved. The guide on understanding the root cause after a repair explains why that matters.
Keep receipts, model numbers and photographs together with your other records, as described in documents that help after electrical damage. Whether any loss is covered depends on your policy and your insurer's decision. Nothing on this page speaks to coverage.
When to call an electrician
Call a qualified electrician if more than one device failed, if a breaker keeps tripping, if lights flicker or dim, if outlets are warm or discolored, if you smell burning or hear buzzing from the walls or the panel, or if you are not sure whether your circuits are safe. If there is smoke, fire or a shock, call 911 first.
When you call, describe what happened, which devices were affected, which circuits they are on if you know, and what you have already done. The dispatcher can explain the service call charge before anyone is sent, and can tell you whether the situation looks like it needs an on-site visit before a quote can be given. Quotes are given by phone, and complicated jobs need an on-site visit.
Call whenever you want a qualified person to confirm that the circuits and equipment are safe before you plug your belongings back in.
Questions people ask
Should I unplug everything after a surge?
Yes, as a precaution, if you can reach the plugs safely and the area is dry. Unplugging protects devices from a second surge when power returns and keeps you from energizing anything that was damaged. Leave devices unplugged until the circuits are checked, then plug them in one at a time and watch for anything unusual.
Can I use a surge protector that was in a surge?
It is best not to. The protective components inside a surge strip wear out as they absorb events, and a strip that took a large surge may no longer protect anything, or may be unsafe. Replace it. For whole-house protection, ask a technician to check whether a protective device was affected.
My appliance works but a breaker keeps tripping. What now?
Leave the appliance off and the breaker off, and have the circuit checked. A repeated trip means the circuit or the appliance has a problem, and resetting the breaker over and over can create heat. A technician can test the circuit and the appliance to find which one is at fault.
Is it safe to turn on electronics that got wet?
No. Powering up wet electronics can cause shorts, damage and, in some cases, fire or shock. Keep them unplugged, remove batteries if you can do so safely, and set them aside. A repair or data recovery professional can advise whether anything is salvageable. Do not try to dry them with heat.
How do I know if my air conditioner was damaged by a surge?
Signs include a unit that will not start, trips breakers, hums without running, or runs poorly after an event. Do not keep trying to start it, since repeated attempts can add damage. Turn the thermostat off and have a qualified technician check the electrical supply and the unit before you run it again.
Who decides whether a damaged appliance is covered by insurance?
Your insurer, under your policy. An electrician or an appliance technician can describe the condition of the equipment and the circuits, and your photographs and receipts support your records, but they do not determine coverage. Call your insurer or agent and ask what they require and what the deadlines are.
About "Appliance Damage: What to Know and Do": call and give us the details, and we will explain what is safe to do while you wait and what the visit would cover. Jobs that cannot be quoted blind need a look on site.
Related pages
- Power Problem Vocabulary: Surge, spike, sag, brownout, blackout and outage are not the same thing. Learn the terms so you can describe your power problem accurately on a call.
- Photograph Damage: What to photograph after an electrical failure, fire, flood or surge, how to do it from a safe distance, and how to keep the images organized for later.
- Insurance Documents: Which records to gather after an electrical failure, fire, flood or surge: receipts, photos, technician findings and notes, without claims about coverage.
- Nearby Lightning: Lightning hit nearby and now devices are dead. Learn how induced surges travel, which equipment fails first, and when the wiring needs an inspection.
- Emergency Permits: How urgent electrical repairs still move through permits and inspections in South Florida, what usually needs one, and what to ask before work starts.
- Emergency Kit for Power: What to keep near your panel and in a grab-and-go kit for electrical emergencies: light, labels, a contact list and info cards, with no live equipment.
