Electrical help for homes and businessesRequest service
Emergency ElectricianCall (954) 481-0910
Emergency Electrician technician installing a pendant light in a bright coastal home

Safety and Guides

Event Lighting: What to Know and Do

Holiday displays, backyard parties, quinceaneras, weddings and street events all lean on temporary power: strings of lights, speakers, inflatables, coolers and cords strung across lawns. Temporary setups fail in predictable ways. This guide explains the limits, the outdoor rules and what to do when a display trips, smells or sparks.

If something is sparking, smoking or hot right now

If a string of lights, a cord, a controller, a speaker or an outlet is sparking, smoking, melting or too hot to touch, treat it as an emergency. If there are flames or smoke, move people away from the area and call 911. Do not use water on electrical equipment, and do not throw water on an outdoor display that is still plugged in.

If there is no fire and the equipment is dry, switch off the display at its controller or switch. If it is safe, unplug at the outlet, gripping the plug and not the cord, with dry hands. If the outlet, plug or cord is melted, wet, sparking or too hot to touch, do not touch it. Keep guests and children away, and if the panel is dry and normal and you can reach it safely, switch off the breaker that feeds the outdoor circuit. Then call.

Do not reset a breaker or a ground-fault outlet repeatedly to keep the party going. A device that trips is telling you that a fault, an overload or water is present. The pages on a hot cord or extension cord and a GFCI that will not reset explain what the technician will look for, and the guide on what never to do in an electrical emergency lists habits that make things worse.

Emergency Electrician technician repairing and testing a wall outlet in a South Florida home

Why temporary setups fail more often

A permanent installation is designed, inspected and fixed in place. A temporary setup is assembled in an afternoon from whatever is on hand. Cords are chosen by length and not by rating, connections are made on the ground, and the person who set it up may not be the person who uses it. Hot weather, rain, foot traffic and children add stress.

Several features of events increase the risk. Equipment is placed outdoors where it can get wet. Loads are added throughout the evening, such as a speaker, a blender, a fog machine, a heater or a second string of lights. Cords run across walkways where people step on them. Guests plug in phones and devices wherever they find an outlet. And the setup is often used for hours in the heat of a Florida evening, which leaves less margin.

The result is that most event electrical problems are overloads, damaged or inappropriate cords, wet connections and heat, all of which can be prevented with planning. The guide on extension cord and power strip limits explains the basics, and the planning steps on this page apply them to lighting and events.

Count the load before you plug in

Every circuit has a limit, and every string of lights, speaker and appliance draws a share of it. Before an event, take a few minutes to list what will be plugged into each outdoor outlet or circuit. A rough count is better than none.

Modern LED string lights draw very little, and many strings can run from a single outlet within their rated limit. Older incandescent strings draw much more, and a long run of them can overload a cord. Read the label on each string. It usually states the maximum number of strings that can be connected end to end. Do not exceed that. Do not connect strings of different types or ratings, and do not use a string whose plug, wire or sockets are damaged.

Other items need their own approach. Heaters, blenders, coffee urns, popcorn machines, kettles, fog machines, inflatables with powerful blowers, and sound systems with large amplifiers draw far more than lights. Give them their own outlets and, where possible, their own circuits. Do not plug them into a strip that already has lights on it. If a breaker trips, find the cause before you reset. The guide on reading a tripped breaker explains how to describe what was running.

Outdoor outlets and wet weather

Outdoor outlets are meant to be protected from moisture and from shock. They should have weatherproof covers that stay closed over a plugged-in cord, and they should be protected by a ground-fault device, often called a GFCI. These devices cut power quickly when they detect a leak of current, for example through water or a person. They have test and reset buttons. Press them according to the manufacturer's instructions before the event.

If an outdoor outlet has a cracked cover, a missing cover, a loose faceplate, rust or water inside, do not use it. Use another outlet, or call to have it checked. If a ground-fault outlet will not reset, do not bypass it with a cord from another room. The device is telling you something is wrong.

In South Florida, afternoon storms arrive quickly. Plan to shut down lighting and unplug connections if rain starts. Keep plugs and connectors off the ground, where puddles form, and raise them on a stand or hang them with the connection pointing down so that water drips off. A connector that sits in a puddle can energize the water, and a child or pet walking through it can be hurt. The page on outdoor outlets and yard electrical safety goes into more detail.

Choosing the right cords and lights

Use products made for the way you plan to use them. Lights and cords sold for indoor use only are not for outdoors. Look for packaging or tags that state outdoor rating, and use only products that have been tested by a recognized laboratory, with the mark of that laboratory on the product or packaging.

Use extension cords that are rated for outdoor use, have a thick enough conductor for the load, and are as short as practical. A cord that is too thin or too long will heat. Do not coil a cord that is carrying a load, since coils trap heat. Do not run cords under rugs, through doorways where doors close on them, or across driveways where cars pass.

Inspect every string, cord and controller before use. Look for cracked insulation, bare wire, loose or missing bulbs, damaged sockets, bent or discolored plugs and signs of past overheating. Discard anything that is damaged. Do not repair with tape. Replace burned-out bulbs with the same type and wattage. For more detail on cords and strips in general, see the page on extension cord and power strip limits.

Fixing lights to the house, trees and fences

How you attach lights matters as much as what you plug in. Do not use nails, staples or tacks through cords, since they can pierce insulation. Use plastic clips or hooks designed for lights, and keep the weight off the wires. Do not wrap lights around metal gutters or railings in a way that stresses cords or lets water collect at connections.

Keep lights and cords well away from overhead power lines and from the service mast and meter at the house. Never use a metal ladder near these, and never throw string over a wire. If a ladder, a pole or a branch touches a line, stay away and call 911 and the utility. The page on a wire touching a tree or fence explains why.

Trees and palms add concerns. Lights wrapped around a trunk or branch can be rubbed through by wind. Lights draped into a tree near a line can be a hazard. If a tree on the property is close to a power line, do not climb it to hang lights. The same goes for a fence that touches a wire, since it can become energized.

Inflatables, speakers, fog machines and DJs

Events often include equipment far heavier than lights. Large inflatables use powerful blowers that draw considerable current and run for hours. They should be plugged into an outlet that is on its own or shared with very little. Sound systems for a party or a band can draw a lot, and their cords often cross the ground. Fog machines and heaters use heating elements, which are heavy loads.

If a hired performer or vendor brings equipment, ask what it needs, and ask which outlet they plan to use. Do not assume that all outlets are equal. A vendor who plans to use a single outlet for a refrigerator, a grill with an electric starter and a sound system is asking for a tripped breaker, and possibly a fire.

Where an event is large, consider asking an electrician to provide a temporary power arrangement or to review the plan. Quotes are given by phone, and a complicated job needs an on-site visit, with a service call charge explained before dispatch. For events in a condominium, clubhouse or community space, check with the association or building manager first, since they own the electrical system. The page on the condominium association electrical emergency explains who handles what.

A pre-event checklist for the day before

A short walk-through the day before catches most of what goes wrong. Do it in daylight, with the equipment in front of you, and write down what you find.

Work through these steps in order:

  1. Decide where each item will plug in, and list what will share each outlet or circuit.
  2. Press the test and reset buttons on every ground-fault outlet you plan to use, and confirm they trip and reset normally.
  3. Inspect each string, cord, controller and plug for damage, and set aside anything that is cracked, bare, discolored or loose.
  4. Check that outdoor covers close over plugged-in cords, and that connectors will sit off the ground and out of puddles.
  5. Plan cord routes away from walkways, doors, driveways and water, and gather cord covers where cords must cross a path.
  6. Locate the main breaker and the breakers for the outdoor circuits, and tell a second adult where they are.
  7. Keep a flashlight, a phone and a written address near the controller in case something fails after dark.
  8. Agree who will shut down the display if weather turns, and when.

A worked example: the backyard celebration that trips twice

A family hosts an evening celebration in a backyard. They string lights across the patio, set up a speaker, plug in a rented patio heater for the cooler part of the night, and run a cooler with a small fridge from a long cord through a window. Everything is plugged into a handful of outlets, a few of which are on the same circuit as the kitchen.

Halfway through the evening, the breaker trips and the lights go out. Somebody resets it. It trips again ten minutes later. A guest suggests running a cord from the neighbor's yard. Instead, one of the hosts follows the plan they wrote down: the heater and the fridge come off the shared circuit, the lights and speaker stay on, and a flashlight is used to check that no plug is hot.

In the morning, they find that one outdoor outlet cover will not close and that the cord from the fridge has been pinched in the window. They call an electrician, describe what tripped and what was running, and have the outlet inspected. The lesson is not that events are dangerous. It is that a plan, a quick check and a willingness to stop resetting a breaker turned a likely hazard into an inconvenience. The page on a breaker that will not reset covers what to do when a breaker trips again right away.

Walkways, guests and children

People are the other half of the picture. Guests step on cords, children grab at lights, and drinks spill. A cord that crosses a walkway should be taped down with a cord cover or routed to the side. A power strip should be placed where nobody will kick it, and where a spill will not reach it.

Do not let children play with cords, plugs or controllers. Do not let guests plug phones or devices into overloaded strips. If a guest points out a hot plug or a smell, take it seriously. A child's or a guest's alertness is often the first warning.

Keep the area around the main outlet and the controller clear, so that anyone can reach the plug or the switch in a hurry. Make sure at least one adult knows where the main breaker is and how to find it in the dark, and that nobody opens the panel if there is water or any heat. The guide on how to find your main breaker helps with that, and the page on protecting children from electrical hazards covers young guests.

Long displays: weeks of running outdoors

Holiday displays often stay up for weeks, which means weeks of heat, sun, rain and wind. Check connections once a week. Look for water in connectors, plugs that have moved, cords that have been chewed by animals or rubbed by branches, and timers or controllers that feel hot. Use a timer so that lights do not run all night, and use one rated for the load and for outdoor use.

Check the outdoor outlet as well. A plug that has sat in an outdoor outlet for weeks can corrode the contacts. If you see rust, green or white deposits, or a cover that no longer closes, replace it. Do not keep using an outlet that is wet inside.

Take the display down at the end of the season and inspect each item before storing. Throw away anything damaged. A set that was fine last season may have cracked insulation this year. The page on an outlet that is warm or discolored describes what a worn outlet looks like.

After the event: checking what you used

When the party is over, take a few minutes to check. Unplug everything and coil cords loosely. Feel the plugs and outlets you used, and look for discoloration or a faint smell. Check the cover plates on outdoor outlets. If a breaker tripped during the event, note which one and what was running. If a ground-fault outlet tripped, note whether it reset normally.

If you saw anything unusual, such as a warm outlet, a flicker, a tripped breaker or a smell, call and describe it. A short visit can find a loose connection or a worn outlet before the next event. When you talk to the dispatcher, mention what you plugged in, how long it ran, and what you noticed.

If you plan regular events, such as weekly gatherings or a seasonal business display, ask an electrician about adding outlets, a dedicated circuit or a properly installed weatherproof receptacle where you need it. That is safer than extension cords, and it gives you a setup you can trust. The page on what to expect when the electrician arrives describes how a visit works.

Questions people ask

How many strings of lights can I connect end to end?

Check the label on each string. It states the maximum number of strings that can be connected, and it differs between LED and older incandescent types. Do not exceed it, and do not mix types. If you need more lighting, use a second outlet or a second circuit instead of stretching the limit.

Is it safe to leave outdoor lights on in the rain?

Only if everything is rated for outdoor use, the connections are protected and raised off the ground, and the outlet has ground-fault protection and a closing cover. If a heavy storm arrives, unplug the display. If anything sparks, trips or smells, stop and have it checked.

My ground-fault outlet outside keeps tripping when it rains. What does that mean?

Water has probably entered a connection, a cord, a fixture or the outlet box. The device is doing its job. Unplug the display, let the area dry, and do not bypass the outlet. If it still trips with nothing plugged in, call an electrician to inspect the outlet and the wiring behind it.

Can I plug a bounce house blower into an extension cord?

Only with a heavy-duty outdoor-rated cord that is as short as possible and rated for the blower's current, and only if the manufacturer allows it. A blower runs for hours, so a thin cord will heat. Give it its own outlet and check the plug by touch after it has run for a while.

Should I call an electrician before a big event?

If you plan heavy loads, a large display or an outdoor setup with many cords, it can help. A technician can check outlets, ground-fault protection and circuits, and advise on safe placement. Quotes are given by phone, and a complicated job needs an on-site visit with a service call charge explained before dispatch.

Talk to Emergency Electrician

Reading about "Event Lighting: What to Know and Do"? Tell us what stopped working and when. We will say what an electrician would check first, and quotes are given by phone when the job can be described.

Related pages

  • Cord Limits: How extension cords and power strips overheat, which devices should never use them, the warning signs to watch for, and safer alternatives to ask about.
  • Outdoor Outlets: Outdoor outlet covers, GFCI protection, sprinklers and tools in wet South Florida yards: what to look for, what to avoid and when to call a technician.
  • GFCI Won't Reset: A GFCI that will not reset means a fault or a failed device. Learn what safe checks you can do, what to avoid, and how to describe the problem by phone.
  • Emergency Permits: How urgent electrical repairs still move through permits and inspections in South Florida, what usually needs one, and what to ask before work starts.
  • Insurance Documents: Which records to gather after an electrical failure, fire, flood or surge: receipts, photos, technician findings and notes, without claims about coverage.
  • Emergency Kit for Power: What to keep near your panel and in a grab-and-go kit for electrical emergencies: light, labels, a contact list and info cards, with no live equipment.

Need to discuss an electrical concern or planned project?

Request service

Related pages

Call (954) 481-0910