First, make sure nothing is burning
Before thinking about electronics, check for danger. If you smell burning plastic, see smoke, hear crackling in a wall, or feel heat from a panel, outlet or device, call 911 and leave the building. Fire first, equipment later. A surge strong enough to destroy a power supply can also heat a connection somewhere in the house, and that heat may take time to show itself.
If someone was holding a phone, touching a plumbing fixture, or standing near a metal door frame during the storm and feels odd, tingling, or has chest symptoms, call 911 and mention lightning. Even a nearby strike can affect people through wiring and plumbing.
If there is no smoke and nobody is hurt, the situation is less urgent but still worth doing in order. Unplug the failed devices, leave tripped breakers alone, and do not use anything that smells hot. Then work through the sections below to understand what happened and who to call.

- Smoke, burning smell or heat: call 911 and leave.
- Anyone with symptoms after the storm: call 911 and mention lightning.
- Unplug failed devices and keep them for documentation.
- Do not keep powering up gear that smells hot or buzzes.
How lightning that did not hit you still gets in
A lightning strike creates a huge, rapidly changing current and a strong electromagnetic field. Any long conductor nearby acts like an antenna and picks up part of that energy. Overhead utility lines, telephone and cable lines, buried service cables, metal fences, and even the wiring inside your walls can have a surge induced in them without being struck directly.
The surge may also arrive by the ground. When lightning hits a tree or the earth, current spreads outward through the soil, and the voltage in the ground near the strike point rises for a moment. Equipment connected to two different grounds, such as the electrical ground and a cable television shield, can see a voltage difference across it. That difference is what destroys the sensitive chips inside a modem or a router.
In practical terms, a near miss can reach your devices through at least four paths: the power line, the cable or telephone line, the antenna or satellite coax, and the ground. Devices connected to more than one of these are the most exposed. That is why a router and a television with a cable connection fail so often together.
Which devices fail first and why
Devices with low-voltage electronics inside are the most vulnerable, because they depend on delicate chips that cannot handle even a brief voltage spike. Modems, routers, set-top boxes, smart TVs, network switches, and home security panels fail frequently. Anything with a long data cable to the outside world, such as a cable modem or a satellite receiver, is a common casualty.
Next come devices with control boards: garage door openers, pool equipment controllers, irrigation timers, smart thermostats, doorbells, and the control boards inside water heaters, air handlers, and heat pumps. These are often the least obvious casualties. A system may appear to simply not start, when in fact a small board has failed.
Simple devices with heavy parts, like lamps, resistive heaters, and plain light fixtures, are usually the most resistant. If a lamp survived and a router did not, that is normal. It does not prove the house wiring is untouched, only that simple resistive loads shrug off what electronics cannot.
What the failure pattern tells an electrician
The pattern of failures is useful information. If devices on one circuit failed and others did not, the damage may have entered through that circuit. If devices connected by a cable or data line failed but power-only devices survived, the surge likely entered through that line. If everything with a power supply failed, the surge came through the main power service.
Another clue is the location of the failures. Equipment near the meter, the service panel, or an outdoor connection point often shows more damage than equipment at the far end of the house, because the surge weakens as it travels through wiring. A cluster of failures near the garage and the exterior wall can point to a path through a specific outdoor circuit.
The timing also matters. Devices that fail instantly in the storm are the obvious ones. Devices that start malfunctioning over the next days or weeks may have been weakened without failing completely. Keeping a simple list of what failed, when, and where it is located helps the technician work out the path.
Does the wiring need checking?
Often yes, at least a basic check. A surge that killed a power supply passed through the house wiring on its way. It may also have damaged the insulation, a connection, a breaker, or a wiring device along that path. Usually the damage is limited, but the only way to know is to test.
The signs that call for more than a quick look include a breaker that now trips for no clear reason, outlets that no longer work, lights that flicker, a hum or buzz from the panel, a warm outlet cover, and a faint burning smell. Any of these suggests the surge hurt something in the wiring, not just the electronics. See the page on breakers that trip after power returns for how those patterns are read.
If only electronics failed and there are no electrical symptoms, the risk is lower, but a short inspection of the panel, the service equipment, the grounding connections, and any whole-house surge protection is still a smart step. If a surge protective device is installed, a technician can check whether it has done its job and needs replacement, because many are designed to sacrifice themselves.
What is safe to do before the electrician arrives
Unplug the damaged devices and anything else that is valuable and not needed. This protects them from a second surge and from power that may still be unstable. Leave tripped breakers where they are. If you do reset one, do it once, with nothing plugged in, and stop if it trips again.
Do not open failed equipment to look inside, particularly anything with a large capacitor such as a television, a power supply, or a microwave. Stored charge can remain inside a device after it is unplugged. Do not open the main panel. Do not plug failed devices into a different outlet to see if they work, because a faulty power supply can damage the circuit it is connected to.
Take photographs of the failed devices, their labels, and any visible damage, and write down model numbers. Make a list of every item that no longer works. This is useful for insurance, for the manufacturer, and for the technician, and it is easy to forget details later.
Inside the visit: what a technician checks
The visit often begins with a conversation about the storm and the failures. The technician then checks the incoming service: voltage on each leg, voltage to neutral, and the condition of the meter and mast. They check the grounding system and the bonding connections, including the ground to the cable and telephone entry points, because a poor ground raises the damage from a nearby strike.
The panel is opened by the technician, who checks for signs of heating or arcing, tests breakers and checks for loose connections. Ground fault and arc fault devices are tested. If a whole-house surge protective device is present, its indicator is checked and, if needed, it is replaced.
On branch circuits, the technician tests the outlets and devices on the affected circuits for proper voltage, polarity, and grounding. Damaged outlets and switches are replaced, and any circuit that shows a fault is traced further. The technician explains what is safe, what is questionable, and what to watch, and gives any repair quote by phone or after the findings are explained.
Common near-miss scenarios in South Florida
In summer, afternoon storms build quickly and lightning is frequent across the peninsula. A strike on a palm tree or on a streetlight can induce a surge in a neighborhood without any direct hit on a house. Houses with long overhead service drops, pool equipment, outdoor lighting, and detached garages are more exposed because they have more conductors acting as antennas.
Scenario one: a single-story home has its router, television, and garage door opener fail after a nearby strike, but everything else works. Likely path: the cable line and the power line. The wiring needs a basic check, and surge protection on the data and power lines becomes a sensible topic.
Scenario two: a condominium unit loses a television and a thermostat, and the neighbor above lost a refrigerator control board. The building service or a common ground may have carried the surge. The unit owner should document the damage and tell the association, because the common systems may be involved.
Scenario three: a pool equipment pad stops working and the breaker will not reset. Pool equipment sits outdoors, is bonded and grounded, and often has long wire runs, so a near strike can damage it. A technician should check the circuit and the bonding before the pump is reenergized. See the page on pool equipment tripping power for the pattern.
Delayed failures and the slow-fade devices
Some of the worst surge damage is the kind that does not show on the night of the storm. A chip that took a partial hit can keep working for days, then fail without warning. A capacitor that was stressed can swell slowly and eventually fail. A connector that was pitted by a tiny arc can become a high-resistance joint that warms up a little more each week. For that reason, the weeks after a near miss are worth watching.
Signs of slow-fade damage include a router that reboots at odd times, a television that shuts off and restarts, a thermostat that loses its schedule, lights that dim when a certain appliance starts, and outlets that feel slightly warm. None of these is proof of a wiring fault, but each is a reason to mention the storm when you call. A technician who knows about the event will test more carefully than one who is told only that an outlet is warm.
It also helps to keep a simple log. Note the date and what you observed, even small things. If a pattern emerges, such as problems on one circuit, that points the technician straight to the section of wiring that took the hit. A log is also useful evidence if a device later fails and you need to connect it to the storm for a claim.
Insurance, manufacturers, and keeping records
Surge damage is a common reason for claims, but each policy differs, so read yours or ask your insurer how it treats lightning and surge damage. Many manufacturers do not cover damage from lightning or surge, so do not assume a warranty applies. Ask rather than guess.
Keep the failed devices until the claim is settled. Keep a list with brand, model, approximate age, and the date of failure. Keep any written findings from the electrician. A report that says the wiring was inspected and that a surge was the likely cause is useful. The page on appliance and electronics damage after an event has more on what to record.
If you plan to replace the failed gear, consider waiting until the wiring has been checked and any surge protection issue is understood. New equipment plugged into a damaged circuit can fail the same way, and it is better to know the house is sound first.
Reducing the next near miss
No protection can promise that nothing will fail in a nearby strike, but layered protection can reduce the damage. The usual idea is protection at the service entrance, which handles the largest surges, plus protection at sensitive equipment, which catches what gets through, plus good grounding and bonding that give the surge a safe path. The page on surge protection after lightning explains the layers in plain language.
Habits help too. Unplug sensitive equipment before a known storm if you are away, and keep a list of what is connected to cable or satellite lines. Know where the main breaker is and that it works. See how to find your main breaker if you are unsure.
When you are ready, call and describe the storm, the failures, and any electrical symptoms. The dispatcher can explain the service call charge and how scheduling works. Quotes for repair work are given by phone, and a larger job needs an on-site visit first. If anything smells hot or you see smoke, call 911 before anything else.
Questions people ask
Can lightning damage my electronics without hitting my house?
Yes. Lightning can induce a surge in overhead lines, buried cables, cable and phone lines, and even in house wiring. It can also raise the voltage in the ground near the strike. Devices connected to power and a data or cable line are the most exposed, which is why routers, modems and televisions fail first in a near miss.
If only electronics died, does my wiring still need checking?
A short inspection is worthwhile. The surge passed through the wiring to reach the device, and it may have weakened a breaker, an outlet or a connection. If there are no electrical symptoms the risk is lower, but a technician can check the panel, grounding, and surge protection and tell you whether anything needs attention.
Why did my garage door opener and thermostat fail?
Both contain small control boards with sensitive chips and are connected to long wires that can act as antennas. A surge induced in those wires or in the power circuit can destroy the board while heavier parts survive. These control boards are common hidden casualties in air handlers, water heaters, pool controllers, and irrigation timers.
Should I plug the failed devices into another outlet to test them?
No. A failed power supply can damage the circuit it is connected to, and a device with internal damage can overheat. Unplug the devices, photograph them and their labels, and keep them. Have the wiring checked first, then decide whether a device is worth repairing or replacing.
Will a surge protector have saved my equipment?
It may have helped, but protection is never a promise. A good protector can absorb part of a surge, but a strike that induces voltage on a data line or a ground may bypass it. Layered protection at the service, at the equipment, and on data lines gives the best chance. A technician can check any protector you have.
When should I call 911 instead of an electrician?
Call 911 for smoke, flames, a burning smell, crackling in a wall, a hot panel, or anyone who feels unwell after the storm. If none of those apply and you simply have dead devices or a breaker that will not hold, an electrician is the right call. When unsure, call 911 first.
Reading about "Lightning Nearby and Equipment Failed"? Tell us what stopped working and when. We will say what an electrician would check first, and quotes are given by phone when the job can be described.
Related pages
- Lightning Strike: A lightning strike on your house can leave hidden electrical damage and fire risk. Learn the safe first steps, the fire watch, and what gets inspected.
- Surge After Strike: After lightning damage, learn how layered surge protection works in plain language: service entrance, point of use, grounding, and what to ask an electrician.
- Surge Device Failed: A whole-house surge device with a red light, alarm or burn marks has done its job or failed. Learn what the indicator means and what to do after a big surge.
- Power Problem Vocabulary: Surge, spike, sag, brownout, blackout and outage are not the same thing. Learn the terms so you can describe your power problem accurately on a call.
- After-Storm Power: What to check before the utility re-energizes your service after a storm, what to leave off, and how to bring a house back online without damage or hazards.
- Pre-Storm Checklist: A calm, practical electrical checklist for the days before a hurricane: what to check, what to charge, what to leave alone and when to call a professional.
