The first minutes: people, smoke, and 911
If you think the house was struck, check on every person first. Anyone who was near plumbing, a phone cord, a window, or an appliance when the strike happened may be shaken or injured, even if they say they feel fine. Lightning can cause heart rhythm problems and burns that are not obvious at first. If anyone is dazed, has chest pain, trouble breathing, or visible burns, call 911 right away and say that lightning was involved.
Next, look and smell for fire. Check the attic access, the ceilings, the walls near outlets and the garage. Smoke, a burning smell, a crackling noise, or a hot spot on a wall means leave the building and call 911. Do not go into the attic to look for it yourself. A fire inside a roof assembly can travel quickly and the air can be filled with smoke and heat.
If there is no smoke and no one is hurt, take a slow walk through the house with your eyes and nose open. You are looking for scorch marks around outlets, a plastic or burnt odor, a dead or dim section of the house, and any popped breakers. Make a mental note and stay out of rooms with a smell. The next steps are about watching for slow fire and getting a qualified inspection, not about repairing anything yourself.

- Anyone hurt, dazed or with chest pain: call 911 and mention lightning.
- Smoke, flames or burning smell: leave and call 911.
- Do not enter the attic to search for a fire.
- No smoke and no injury: begin a careful fire watch.
Why a lightning strike can start a fire hours later
Lightning carries a large amount of energy for a very short time. When it enters a structure, it looks for a path to ground, and that path may run through roofing, framing, plumbing, antenna cable, and electrical wiring. Where the current passes through a poor conductor, such as wood or damp insulation, it can generate intense local heat. A small ember inside a wall cavity or in attic insulation can smolder for a long time before it breaks into open flame.
This is why strike aftermath is treated as a fire watch situation. A house can look and feel normal after the event and still have a hidden heat source. The usual advice from fire services is to remain alert for several hours and to have the structure checked even if nothing seems wrong. Thermal imaging by the fire department is one way crews check for hot spots without opening walls.
Electrical wiring adds a second route. If the strike entered through the electrical service, the surge may have partly melted wire insulation or damaged connections inside the panel, in junction boxes, or at outlets. That damage may not trip a breaker, because a breaker responds to current over time, and a surge is too brief. The damaged spot can then heat later under ordinary use.
Doing a safe fire watch
A fire watch means periodically checking for signs of heat or smoke in the places most likely to hide a problem. Do it by sight, smell, and touch of surfaces from the outside, never by opening walls or climbing into tight spaces. Check the ceiling below the attic, the walls around the main panel, the garage, and any room where you heard a bang or saw a flash. Look at the back of the garage and the area around the meter outside.
Keep a charged phone, shoes, and a flashlight close by, and know your exit route. Keep smoke alarms in place, and do not disable one because it chirps. If the strike knocked out the alarms, check whether they are hardwired and whether the backup battery is working. A chirping alarm after a strike is a sign that the alarm circuit may have been affected.
If there is a smell or a warm area, do not wait. Call 911, get out, and let the fire department decide whether the structure is safe. Remember that a fire department visit is not a sign that you did something wrong. They would much rather open one wall than respond to a full structure fire later. The page on fire department visits and electrical reinspection explains what usually follows.
Reading the signs of electrical damage
The most obvious signs of a strike are visible: scorching on a wall plate, a blown-out outlet, a split in a cable sheath, or a dead patch of lights. The less obvious signs matter more. Look for lights that now flicker, outlets that no longer work in a room that did before, breakers that trip immediately, a hum from the panel, or a sharp odor near the meter or the service mast outside.
Electronics are a sign, too. If a router, a television, a garage door opener, a smart thermostat, and a water heater control board all failed at once, the surge moved through the house wiring and not just through one device. That kind of widespread damage raises the odds that wiring devices, not only electronics, were hit. For more on how the surge reaches equipment, see the page on nearby lightning and failed electronics.
Do not use the term working to mean safe. A circuit that still powers a lamp may have a damaged conductor or a weakened connection that will overheat under a heavier load. After a direct strike, an inspection is about proving that wiring and equipment are sound, not about checking whether the lights come on.
What not to do after a strike
Do not reset a tripped breaker repeatedly or reenergize a section of the house that smells, sounds or looks wrong. If the main breaker tripped, leave it off until someone qualified has looked at the panel and meter. Do not touch the panel if the floor is wet or if the cover is hot or discolored.
Do not use a ladder to look at the roof, the mast or the weatherhead. A strike may have damaged the mast or loosened the service cable, and that cable is energized from the utility side. Do not try to reseat a pulled meter, and do not touch the lines going from the pole to the house. If you can see damage on the utility side of the connection, keep clear and call the utility.
Do not run extension cords from a neighbor or a generator into a damaged house. Connecting a generator to the house through a cord into an outlet can energize the wiring in reverse and endanger utility crews. See the page on generator backfeed risk for why this matters.
- Do not repeatedly reset breakers that trip.
- Do not climb to the roof or touch the mast, weatherhead or meter.
- Do not open walls, ceilings or the panel cover to look for damage.
- Do not plug the house into a generator through a cord.
What an electrician inspects after a strike
The inspection begins at the service entrance. The technician looks at the meter socket, the mast, the weatherhead and the service conductors for burn marks, melted insulation, or loosened parts. They check the grounding system, because lightning energy relies on the grounding electrode and bonding connections to find its way to earth. A corroded or broken ground conductor changes where that energy goes.
Inside, the panel is examined with the cover removed by the technician. They look for pitting or burn marks on bus bars, discolored breakers, signs of arcing, and loose lugs. They test voltage at the main and at each leg, and they test the neutral and ground connections. Breakers may be checked for proper operation, since a surge can leave a breaker that no longer trips correctly.
Then they work through branch circuits and devices. Outlets, switches, junction boxes, smoke alarm wiring, and fixtures near the point of entry are checked, and any that show heat damage are replaced. Where a circuit shows insulation breakdown, the technician may isolate it until the damaged section is found. Attic wiring is a particular concern, because it is often in contact with insulation and framing.
Hidden damage: where it hides and how it is found
Lightning damage is rarely uniform. One outlet can look fine while the cable behind it is cooked. Cable runs through framing and insulation, so the damage can be at a staple, a splice, or a spot where the cable crosses a nail plate. Connections inside metal boxes can be partially fused, creating a high-resistance joint that heats up when current flows.
A technician finds these problems by testing, not by looking. Insulation resistance tests apply a test voltage to a circuit with the power off and measure whether the insulation is leaking current to ground. Thermal imaging, when available, can reveal a connection that is warm under load. Continuity testing can show a break in a conductor, and voltage drop checks can show a bad connection under load.
Some damage is only found when a section is opened. A responsible technician will explain what they found and what they suspect, so you can decide whether to authorize opening a wall or replacing a run of cable. Complicated repairs need an on-site visit before a quote can be given, and quotes are given only by phone after the findings are explained.
Appliances, the service, and what may need replacement
After a direct strike, some parts of the electrical system are more likely to need replacement than repair. Surge-damaged breakers, outlets that have burned contacts, cracked or scorched switch plates, damaged smoke alarm wiring, and failed GFCI devices are common candidates. If the panel shows internal burn marks or the bus bar is pitted, replacement of the panel may be the safer path than patching it.
Service equipment such as the meter socket and the mast may also be damaged. If the customer-side service equipment is damaged, it must be repaired before the utility will reconnect or keep service on. The utility handles its own lines and the meter itself, and the electrician handles the mast, weatherhead, meter socket and everything past it. See the page on storm-damaged meter and mast repairs for the split in detail.
Appliances and electronics may need their own diagnosis. A technician can usually say whether the house wiring is safe, but they cannot say whether a particular appliance's internal circuit board survived. For those, the manufacturer or an appliance repair specialist is the right next call, and the documentation you gather will help with any insurance claim.
Documenting for insurance and for yourself
Start documenting while the details are fresh. Photograph every visible sign of damage: scorch marks, damaged devices, the panel with the door open if it is safe to do so, and any burned or split cable. Photograph the whole room, then close-ups. Write down the time of the strike, what you heard and saw, which devices failed, and which breakers tripped.
Keep the failed devices if you can, rather than throwing them away. An adjuster may want to see them, and a technician can sometimes tell from a failed device which way the surge traveled. Keep receipts and written findings from the electrician, and ask for the findings in writing. The page on getting a written findings report explains what such a report usually includes.
Do not throw away the paper trail from a fire department visit either. If a crew checked the home with a thermal camera, ask for the incident number. These records show that you acted promptly and responsibly, and they help later if a hidden problem emerges.
Living with the house after the inspection
Once a technician has inspected and repaired the damage, ask what they found and what they could not verify. If any area of wiring is suspect but could not be opened, ask what to watch for. Common signs are a warm outlet or switch plate, a faint burning odor, buzzing from a wall, or breakers that trip with no clear cause. Report those quickly.
Consider protection for the future. A strike on the house shows that the building is exposed, and the layered protection concepts on the page about rethinking surge protection after lightning are worth reading. No device makes a house immune to a direct strike, but good grounding and a layered approach can reduce the damage.
When you are ready to arrange the inspection, call, describe the strike and any damage you have seen, and ask the dispatcher about the service call charge and scheduling. Quotes for repair work come after the findings are explained. If the situation changes to smoke, heat, or a burning smell, call 911 first.
Questions people ask
Do I need an inspection if nothing looks damaged after a lightning strike?
Yes, it is wise. A strike can leave hidden damage in the panel, the grounding system, or wiring inside walls that will not show on the surface. A qualified technician can test insulation and connections without opening everything. Even if the lights work, a weakened connection can heat later under load. An inspection is the way to prove the system is sound.
How long should I watch for fire after a strike?
There is no fixed time. Lightning can leave a smoldering spot that takes hours to show itself, so stay alert the same day and night and check for smoke, burning smells, and warm walls. If the fire department used a thermal camera and found nothing, that is reassuring. Call 911 at once if you smell or see anything unusual.
Is it safe to use the lights and outlets that still work?
It is not a safe assumption. A circuit can power a lamp while carrying a damaged conductor or weakened connection that overheats under a heavier load. Keep use light, avoid heaters and large appliances, and leave any circuit that smells, buzzes or feels warm switched off until a technician has inspected the house.
Who repairs the mast and meter if lightning damaged them?
The mast, weatherhead, meter socket and wiring past the meter belong to the customer side and are repaired by an electrician. The utility owns the meter and the lines up to the connection point. If customer-side equipment is damaged, the utility generally will not reconnect until it is repaired, so an electrician is needed first.
Can I reset breakers that tripped during the strike?
Do not keep resetting them. If a breaker tripped from the surge and will hold after one careful reset with nothing plugged in, use it lightly and watch it. If it trips again, leave it off. If the main tripped, leave it off until an electrician has looked at the panel and the meter.
What should I tell the dispatcher when I call?
Say that lightning struck the house, whether anyone was hurt, whether there is any smell or smoke, which breakers tripped, which devices failed, and whether the meter and mast look damaged from the ground. Give your address and a callback number. Ask about the service call charge and scheduling before dispatch.
About "After a Lightning Strike on the House": call and give us the details, and we will explain what is safe to do while you wait and what the visit would cover. Jobs that cannot be quoted blind need a look on site.
Related pages
- Nearby Lightning: Lightning hit nearby and now devices are dead. Learn how induced surges travel, which equipment fails first, and when the wiring needs an inspection.
- Surge After Strike: After lightning damage, learn how layered surge protection works in plain language: service entrance, point of use, grounding, and what to ask an electrician.
- Small Fire: Small flames at an outlet, cord or appliance still mean get out and call 911. Learn why water is wrong, when an extinguisher is an option and what follows.
- Insurance Documents: Which records to gather after an electrical failure, fire, flood or surge: receipts, photos, technician findings and notes, without claims about coverage.
- After-Storm Power: What to check before the utility re-energizes your service after a storm, what to leave off, and how to bring a house back online without damage or hazards.
- Pre-Storm Checklist: A calm, practical electrical checklist for the days before a hurricane: what to check, what to charge, what to leave alone and when to call a professional.
