The first decision: leave and call 911
If flames are visible at an outlet, a cord, an appliance, a light fixture or the electrical panel, the first move is to get everyone out of the building and call 911 from outside. That is the correct answer even when the flames are small, even when they seem to be going out, and even when you think you could handle it. A small flame in electrical equipment is often only the part you can see. Behind the wall, inside the appliance or in the ceiling, insulation and framing may already be heating.
Electrical fires also behave differently from a candle or a pan on the stove. The source can stay energized and keep feeding heat while you try to deal with it. The fire can climb inside a wall cavity or travel along a cable into the attic, where it grows unseen. Smoke from burning wire insulation is toxic, and a few breaths in a closed room can leave you disoriented when you most need to move.
So the order is simple. Get people out first, including children, older relatives and pets that can be carried or called. Close the door behind you if it is safe to do so, because a closed door slows both flames and smoke. Meet at a spot away from the house, count heads, and call 911 with the street address and what you saw.

Do not go back in for belongings, even for something important. Items can be replaced. Everything that follows on this page, from extinguishers to the electrician call, matters only after you and the people with you are safe outside.
Why water is the wrong answer
Many people instinctively reach for a pot of water, a hose or a wet towel. For flames at electrical equipment that is dangerous. Water conducts electricity, and the stream that you throw can carry current back to you through the water, the floor or the container. The result can be a serious shock on top of a fire.
Water can also spread the problem. It may splash onto other energized parts, cause new shorts, or carry the fire to a different spot by pushing burning material around. In a panel or an outlet box, water can make an arc worse before it makes the flame smaller.
Water is still the right tool for some other fires, and in a house with a lot of ordinary fuel the fire department will use water after the power has been disconnected. That distinction is what matters: once the supply is cut by the fire crew or the utility, water becomes a safe choice for them. Before that, leave it alone.
The same applies to a damp towel thrown over equipment, because a wet cloth contacting live parts creates a path for current. A dry, heavy blanket thrown over a tiny flame at a lamp or a small appliance is sometimes suggested, but it asks you to stand close to a live source and it can trap heat. For this site's purposes, the simplest safe advice is still to leave, and to let the fire department decide how and when to use water.
When a fire extinguisher is even an option
There is a narrow situation where using a fire extinguisher may be reasonable. All of the following should be true: the fire is very small and confined, such as a single wastebasket-sized flame or a small appliance; everyone else is already out or leaving; you have a clear exit behind you and are standing between the fire and that exit; you have the right type of extinguisher; and you know how to use it. If any one of those is missing, do not try.
The right type matters. A multipurpose dry-chemical extinguisher labeled for ordinary combustibles, flammable liquids and electrical equipment is the common household choice. A water-only extinguisher is not suitable for electrical fires. The label on the cylinder tells you what it is rated for, and it is worth reading that label before you ever need it.
If you do use one, remember the sequence most manufacturers print on the cylinder: pull the pin, aim low at the base of the flame, squeeze the handle, and sweep side to side. Stay back at the distance the label recommends. If the fire does not go out quickly, or if it grows, flares back or produces heavy smoke, drop the extinguisher and leave immediately.
Even a fire that appears fully out still needs a call to 911 and an inspection. Electrical fires can smolder inside walls and reignite after the visible flame is gone. A technician should also check what caused it before anyone turns the circuit back on. The guide on how electrical fires start explains the usual causes.
What to do about the power while you are leaving
Cutting the power is a good idea only if it can be done without delay and without risk. If the main breaker is in a dry, clear area on your way out, and the panel itself is not on fire, hot or sparking, switching it off can remove the energy feeding the fire. If the panel is the source, or if reaching it means walking through smoke or standing in water, skip it entirely.
Do not unplug a burning cord or appliance. Reaching toward a flame is a bad trade even if the plug looks within reach. Do not use a light switch near the fire as a way of shutting it off. If you are not certain about the main breaker's location, the guide on finding your main breaker is worth reading ahead of time, so the knowledge is already there on a bad night.
Once you are outside, do not go back in to flip a switch. The fire department, along with the utility if needed, can disconnect service at the meter or the pole. Tell the dispatcher that the fire involves electrical equipment, so crews arrive aware of it and can request the utility.
If anyone was touching the equipment when the fire began, or felt a shock, tell the dispatcher at once. A person who has been shocked may need medical attention even if they seem fine, and that is covered in a person shocked at home.
Common starting points for small electrical flames
Knowing where small fires typically start helps you spot them early and also explains why the advice is so firm. Outlets and plugs are the most frequent source: a loose receptacle, a plug that is not fully seated, or a worn contact produces resistance, and resistance produces enough heat to ignite plastic. A power strip loaded with space heaters or window units can overheat the strip itself or the outlet it sits in.
Cords and extension cords come next. A cord pinched under a door or a rug, nicked by a chair leg, or run through a bundle of other cords can have damaged insulation and hidden heating. Light fixtures and ceiling fans can burn when a bulb exceeds the fixture's rating, when a connection in the box has loosened, or when insulation sits too close to a recessed light.
Appliances matter too. A toaster oven, a coffee maker, a dryer with lint, a window air conditioner or a portable heater can ignite from an internal failure. Panels and breakers are less common sources but more serious when they burn, because they sit at the heart of the system and feed many circuits.
Related events often look like a lesser version of the same problem. If you have seen sparks without flames, see sparks from an outlet. If a smell came first, a burning smell with no visible fire describes what that usually means. In all of these, early action keeps a smell or a spark from becoming flames.
After the fire department leaves
When the fire crew declares the scene safe, the power to the affected area is often left off, and sometimes the whole house is disconnected at the meter. This is normal and it is protective. Do not try to restore power yourself, even if the visible damage looks small. Do not reset breakers, flip the main back on, or plug things in to test whether they still work.
The fire department may tell you that an electrician needs to inspect the system before service is reconnected. In many cities and counties, repairs to damaged electrical equipment and reconnection after a fire require an inspection and may require a permit. A contractor can walk you through the general process, and the local building department decides the specifics. The guide on fire department visits and electrical reinspection explains how those steps fit together.
If the fire was confined to one appliance or outlet, the technician's job is to find out why it happened, make sure nothing else on the circuit was damaged, and restore safe power. If the fire involved wiring, a panel or a meter base, the scope can be larger, and the technician will describe what is needed after seeing the damage.
Take care of yourself and the household first. Make sure everyone has been checked for smoke exposure if needed. Then call an electrician when the fire department says it is appropriate, and tell the dispatcher what the crew reported.
What to document, and what to leave undisturbed
After the emergency, record what you can without entering unsafe areas. Photograph the outside of the home, and the affected rooms from the doorway if the fire department says it is safe. Note the time the fire started, what was running or plugged in, and any warning signs beforehand, such as a smell, a flicker or a tripped breaker.
Leave the damaged equipment where it is as far as possible. The failed outlet, cord or appliance can help a technician and an insurance adjuster understand the cause. Do not clean, throw away or reassemble parts until they have been looked at. If something has to be moved for safety, take a photo first.
Keep receipts and records of the work that follows, and ask the technician for a written description of what was found and what was repaired. Our guides on photographing damage before repairs and electrical damage and insurance documents cover what is typically useful.
Avoid giving a cause to anyone as fact before it has been examined. Say what you saw and what you smelled. A technician's findings are more reliable than a guess made in the first minutes, and a clear, calm account helps everyone, from the dispatcher to the adjuster.
Preventing the next one
A fire that has been put out should prompt a look at the whole picture, not only the point where flames appeared. A technician can inspect the circuit that failed, the panel that feeds it, and similar circuits in the home, looking for loose connections, overloaded outlets, aging devices and signs of earlier overheating.
At home, a few habits reduce risk. Plug heavy appliances directly into wall outlets rather than power strips. Replace cords that are cracked, stiff or warm. Do not run cords under rugs or through doorways. Use bulbs that match fixture ratings. Keep space around heaters and window air conditioners, and give them their own appropriate circuits. The guide on space heaters and window air conditioners goes into detail.
Working smoke alarms and a household plan matter as much as any wiring repair. Test alarms on a schedule that suits the manufacturer's directions, and make sure every sleeping area has one. Agree on a meeting spot outside and make sure everyone knows to leave first and call afterward.
If any outlet, switch or appliance has ever buzzed, sparked, smelled or felt hot, have it examined. Small warnings are usually the best moment to act, in terms of both safety and the size of the repair. If you are unsure whether something qualifies, call and describe it. A short conversation can tell you whether a visit is needed, and a technician can guide you toward the right next step.
How the electrician call works after a fire
When you call an electrician after a fire, say first whether the fire department has been involved and whether the power is currently on or off. Describe where the fire was, what was involved, and whether anything else tripped, buzzed or smelled before or after. Give the address and tell the dispatcher about any access issues, such as a gate, a locked meter room or a tenant who holds the keys.
The dispatcher will explain how the visit works. There is a service call charge, and it is explained on the phone before dispatch. Quotes for repair are given by phone, and complicated jobs need an on-site visit so the quote matches the actual damage. You will not be asked to agree to a scope that nobody has seen.
On site, the technician will first confirm that the area is safe, then find the origin, check connected circuits, test the equipment feeding the failed point, and explain what is needed to make the system safe again. Some repairs can be made during the visit. Others, such as panel replacement or rewiring a damaged section, take planning and may involve a permit.
If you are standing outside right now, with the fire department on the way, the single most useful thing you can do is stay out and stay safe. When the scene is cleared and you are ready to deal with the repair, call and tell us what happened. We will take it from there.
Questions people ask
Should I try to put out a small fire at an outlet myself?
The safest choice is to leave and call 911 from outside. Flames at an outlet may be only the visible part of heating inside the wall. An extinguisher is an option only for a very small, confined fire when everyone is out, you have a clear exit behind you and the right type of extinguisher. If any of that is missing, leave. Property can be replaced.
Why can't I use water on an electrical fire?
Water conducts electricity, so a stream or splash can carry current back toward you or spread it to other parts. It can also create new shorts and make an arc worse. Once the fire department or utility has disconnected the power, crews use water safely. Before that, stay out of reach and let trained responders decide how to handle it.
The flames went out by themselves. Do I still need to call 911?
Yes. Electrical fires can smolder in walls, ceilings and insulation and reignite later, sometimes hours afterward. Responders can check hidden spaces with proper equipment, and they can ask the utility to disconnect power if needed. After the all-clear, an electrician should inspect the equipment and the circuit before anything is turned back on.
Is it okay to flip the main breaker on my way out?
Only if the panel is clear of smoke, heat and sparks, the floor is dry, and reaching it takes no extra time or risk. If the panel is the source or the path to it is smoky or wet, skip it. Leaving safely and calling 911 matters most, and the fire department or utility can disconnect service.
Can I use the circuit again if the damage looks small?
Not until a qualified electrician has inspected it. Small visible damage can hide burned insulation, loose terminals or a failed breaker behind the surface. Keep the circuit off, leave the damaged parts in place for the inspection, and describe what happened when you call. A technician can tell you what is safe and what needs repair.
How is pricing handled after an electrical fire?
Quotes are given only by phone, and larger or more complicated jobs need an on-site visit first so the quote reflects the real damage. There is a service call charge, and the dispatcher explains it before anyone is sent. If a permit or inspection is involved, the contractor can explain that process in general terms. Call when the scene is safe.
If "A Small Electrical Fire Just Started" matches what is happening, call and describe it plainly: the room, the breaker, any burning smell or tripped circuit. We explain what the repair would involve before a visit is set.
Related pages
- Outlet Sparks: Sparks from a wall outlet are an electrical emergency. Learn the safe order of steps, when to call 911, and what to tell the electrician on the phone.
- Panel Smoke: Smoke from a breaker panel is a 911 event. Learn what to do while waiting, what the fire crew does, and how the electrician visit follows afterward.
- How Electrical Fires Start: A plain explanation of how arcing, overheated connections and overloaded wiring can start a fire inside walls and panels, and what to do when you suspect one.
- After Fire Crew: What happens electrically after firefighters leave: utility disconnects, red tags, qualified repair and reinspection before power is restored to the building.
- 911 Script: Calling 911 about sparks, smoke, a shock or a downed wire? These are the facts that help dispatch most: address, hazard, people at risk and power status.
- Warm Outlet: A warm, browned or melted outlet is a heat warning. Learn how to read the damage, what to unplug, when it is a same-day call, and what a technician checks.
