Electrical help for homes and businessesRequest service
Emergency ElectricianCall (954) 481-0910
Emergency Electrician technician assessing exterior electrical equipment after South Florida rain

Emergencies

Getting Shocked From a Faucet or Pipe

Metal plumbing is meant to be at ground, so a shock from a faucet, pipe or metal fixture signals a serious fault. This page explains why to stop using it at once, who to call and in what order, and what a technician and a plumber will each look at.

Why plumbing should never shock you

Metal water pipes and fixtures are connected, directly or through bonding wires, to the home's grounding system. In normal conditions they sit at the same electrical potential as the earth, so touching a faucet while standing on a wet floor should feel like nothing at all. If you feel a tingle, a buzz or a jolt, then something has put a voltage onto the plumbing. That is a sign of a fault, and the fault may be inside your home, in a neighbour's home, or in equipment outside.

Water adds to the danger. Wet skin, wet floors and flowing water lower the resistance of the path through your body, and a faucet is often touched together with a sink, a counter or a metal drain. A fixture that gives a faint tingle to dry hands may deliver a much stronger shock to someone standing in a bath or a wet shower. That is why the safest response is to stop using the fixture entirely, not to see how bad it is.

It also means the problem is not limited to the faucet. If one metal fixture is energized, others connected to the same piping may be too. Treat the whole plumbing system as suspect until a qualified person has tested it.

Electrical diagnostic camera, insulated tools, safety glasses, gloves, and Emergency Electrician branded equipment

What to do in the first moments

If you feel a shock from a faucet, pipe or fixture, let go and step back. If you cannot let go, or if another person is stuck, do not touch them. Call 911 at once, and if it is safe and the panel is dry and reachable, switch off the main breaker. Do not stand in water to do so. Our page on someone shocked at home describes the steps.

If the shock was brief and nobody was hurt, stop using the sink, shower, bath or any fixture that gave a shock. Do not touch the plumbing with wet hands. Keep children and pets away from the bathroom and kitchen sink. Do not run water if you do not need to, and do not take a bath or shower until the fault has been found. Use another bathroom if there is one that does not share the same fault, but treat it with caution too.

If you can safely do so, switch off the breaker for the area where you got the shock. If you are not sure which breaker, switching off the main breaker is an option if the panel is dry and in good condition, using the guidance in when it is safe to use the main breaker. Note that turning off the home's power does not always remove a fault that comes from outside the house, such as a utility neutral problem or a neighbour's fault.

  • Let go and step away without touching anyone who is still in contact
  • Call 911 if anyone could not let go, was hurt or has chest pain
  • Stop using the faucet, shower, bath and sink
  • Keep children and pets away from the area
  • Switch off power only if the panel is dry and you can reach it safely
  • Do not stand in water or touch metal fixtures with wet hands

Calls to make and the right order

The order depends on what happened. Call 911 first if anyone was injured, could not let go, lost consciousness, has chest pain or burns, or if there is smoke, sparking or a burning smell. After that, call an electrician urgently, since the source of a voltage on plumbing is almost always electrical. A plumber alone cannot find it, though a plumber is often needed later.

If the shock is mild and nobody is hurt, you can call the electrician first. Tell the dispatcher that metal plumbing is giving shocks, because it affects how the visit is planned. It is also sensible to tell the utility if you suspect the problem is on the supply side, such as a neutral problem on the service line. Utility staff can check the meter, the service connection and the transformer, which are not the electrician's to work on.

If you are in a condo or an apartment building, notify the building manager or the association too, because plumbing is often shared between units and a fault in one unit can show up in others. See condo unit power loss, who to call for how responsibilities divide. Our guide on utility or electrician, who fixes what explains the dividing line.

What can put voltage on plumbing

A frequent cause is a fault in an appliance or fixture that is connected to the plumbing, such as a water heater with a failed heating element, a dishwasher or washing machine with a leak into its electrical parts, a garbage disposal with a damaged motor or an electric fixture on a metal pipe. If the fault current finds a path through the water or the pipe to ground, the pipe carries voltage.

Another common cause is a problem with the grounding or bonding system. Homes are supposed to have the plumbing bonded to the electrical ground so that any stray voltage is carried away. If a bonding wire has been cut, corroded or never installed, a fault elsewhere can leave the plumbing energized. Plastic pipes in parts of the system, which break the metal path, can complicate things as well, and a repair that inserts a plastic section can isolate part of the metal piping.

A third cause is on the supply side: a loose or open neutral on the service line can push return current onto grounded metal, including plumbing. In that case, you may notice other symptoms, such as lights that vary in brightness. Our page on loose neutral symptoms describes them. Finally, in rare cases, a neighbour's fault or a buried line can send current through shared underground pipes.

Dangers that are easy to miss

Water carries electricity into places you may not think about. A person standing in a bath who touches a metal tap could receive a shock that is stronger than the person at the sink, because the contact with water is complete. A child washing hands at a sink may be more vulnerable than an adult. A pet drinking from a metal bowl on a floor that is wet may also receive a shock. If anyone in the household has a pacemaker or heart condition, a shock of any size deserves a medical call.

Another hidden danger is that the fault may not be constant. A voltage on the plumbing can appear when a particular appliance starts, when the air conditioner cycles or when it rains, and then disappear. That makes it tempting to believe the problem has gone away. It has not. Intermittent faults are often worse to trace and just as dangerous in the moment.

Repair work can also expose a person to the hazard. A plumber who cuts into a pipe that carries voltage can be shocked, and a pipe that is energized can send current to another pipe fitting through a wrench. If you have a plumber scheduled for other reasons, tell them about the shock before they begin. Our page on wet hands, wet floors and electricity covers why damp conditions matter.

What the electrician will test

A qualified technician will begin with a safe approach to the area, avoiding contact with plumbing until it is tested. They will measure voltage between the plumbing and a known ground, between the plumbing and the neutral, and between different fixtures. Where there is a voltage, they will try to find out which circuit or appliance is the source by switching off breakers one at a time and watching whether the voltage disappears.

They will inspect the bonding between the plumbing and the electrical system, usually at the water heater, the main water entry and the panel's ground connection. They will check the ground and neutral connections at the panel and at the meter, and they may measure for neutral problems under load. If a specific appliance is the source, they will isolate it and recommend that it be repaired or replaced.

If the supply side is suspect, they will coordinate with the utility. In some cases the utility must repair a neutral on the service line or at the transformer. See urgent ground fault tracing for the type of work involved. Quotes are given by phone for straightforward items, and complicated jobs need an on-site visit. There is a service call charge, explained on the phone before dispatch.

Where the plumber comes in

Once the electrician has found where the voltage comes from, plumbing questions may remain. If the cause was an appliance connected to the pipes, such as a water heater, the appliance may need a plumber as well as an electrician, since replacing a heater involves both water connections and electrical wiring. If a section of metal pipe has been replaced with plastic and has broken the bonding path, a plumber and electrician may need to work together to restore proper bonding.

Do not allow anyone to cut or remove sections of plumbing before the electrician has confirmed that the pipe is de-energized. In some cases the electrician will install or repair a bonding jumper across a section of pipe, which keeps the path continuous. It is a simple device, but it matters.

If you rent or live in a condo, the responsibility for plumbing and for the bonding may be divided between you and the landlord or association. See home or rental, which repair is yours for guidance. Document the shock event and tell the owner or manager promptly.

Getting through the days until repair

Until the fault is fixed, avoid contact with the affected plumbing. If hand washing, cooking and bathing are needed, consider using a different, unaffected bathroom or a temporary arrangement, and ask the electrician what is safe. Do not run the dishwasher or washing machine if they might be the source. Do not use the water heater if it may be the source. Keep the main water valve location in mind so that it can be shut if a leak occurs.

If the shock was mild and no source has been found, do not return to normal use just because a day has passed. Keep a log of when the tingle happens, such as only when the air conditioner runs, only after rain or only when the washing machine is on. This helps the technician. A phone video is not necessary. Notes are enough.

If the power has to stay off in the meantime, protect food and medicine, and use a battery lantern and not candles. If you have a generator, do not connect it to the house wiring or run it indoors. See generator backfeed risk for why.

South Florida homes and why this shows up here

Several features of local housing make plumbing shocks something technicians see more than once. Many homes have a water heater in the garage, where humidity and a concrete floor work against electrical equipment, and where a failing heating element can leak current into the tank and pipes. Homes with copper or galvanized piping that has been partly replaced with plastic can have gaps in the metal path. Older neighbourhoods may have had service work that left the bonding connection loose, and salt air speeds corrosion at clamps and lugs.

Condos and townhomes add shared risers and common grounding, so a shock in one unit may point to the building. Homes with pools carry a further bonding network that ties metal parts together, and a fault there can show up as a tingle in the kitchen or bathroom. None of this means your home has a problem by default, but it explains why the right response to any shock from plumbing is an electrical check and not a guess.

Calling for help

A shock from plumbing is a symptom that should lead to a prompt call. When you speak to the dispatcher, give your address, say which fixture gave the shock and where, whether anyone was hurt, whether water was running or the person was wet, and what you have done. Say whether you switched off any breaker and whether you called 911.

Tell them whether other fixtures feel the same, whether the problem comes and goes and whether any appliance seems related. If you are in a condo or an apartment, mention it. The dispatcher may ask a few questions to judge urgency, and will explain the service call charge before dispatch.

When you are ready, call and describe what happened. A qualified technician can test the plumbing, trace the source and explain what repairs are needed.

Questions people ask

Why would a faucet or pipe give me a shock?

Plumbing should sit at ground, so a shock means some voltage has reached it. Causes include a fault in a connected appliance such as a water heater, a missing or broken bonding connection between the pipes and the electrical ground, a loose neutral on the service, or in rare cases a neighbouring fault. An electrician must test to find which.

Is it safe to keep washing my hands if the shock is mild?

No. Water lowers skin resistance, so the same fault can give a much stronger shock to wet hands, a child or someone in a bath. Stop using the affected fixture, keep children and pets away, and call an electrician. If another bathroom is clearly unaffected, use caution there, but treat the system as suspect.

Should I turn off the water or the power?

The danger is electrical, so the priority is power. If the panel is dry and easy to reach, switching off the relevant breaker or the main can help, but a supply-side fault may remain. Do not stand in water to reach the panel. If anyone is stuck to the fixture or hurt, call 911 and do not touch them.

Who fixes this, an electrician or a plumber?

Start with an electrician, since the source of voltage on plumbing is almost always electrical. A plumber may be needed afterward if an appliance connection or a pipe section has to be repaired or if bonding needs to be restored. If the cause is on the utility side, the utility must fix its own equipment.

The shock stopped. Do I still need a visit?

Yes. Faults on plumbing can be intermittent and appear only with certain loads, rain or when a particular appliance runs. Not feeling it now does not show that the cause is gone. Keep notes of when it happened and call, so a technician can test while the conditions might be recreated.

What if I live in a condo?

Plumbing may be shared across units, so tell the building manager or association right away, along with calling an electrician. The cause may be in your unit, a neighbouring unit or building equipment. Responsibility for repairs is often divided between owner and association, and the manager can coordinate access for testing.

Talk to Emergency Electrician

About "Getting Shocked From a Faucet or Pipe": call and give us the details, and we will explain what is safe to do while you wait and what the visit would cover. Jobs that cannot be quoted blind need a look on site.

Related pages

  • Appliance Tingle: A tingle or mild shock from a metal appliance casing can point to a grounding fault. Learn the triage steps, who to call, and what a technician will test.
  • Shock Victim: If someone was shocked at home, call 911 first and do not touch them while still energized. Learn the safe order of steps and the electrical check afterward.
  • Loose Neutral: Lights that get brighter in one room and dimmer in another, buzzing and failing electronics can mean a loose neutral. Learn the signs and why it is urgent.
  • Wet Floors and Shock: Why moisture changes electrical risk, how wet skin and wet floors raise shock danger, and how to position yourself and get help when water is near power.
  • Small Fire: Small flames at an outlet, cord or appliance still mean get out and call 911. Learn why water is wrong, when an extinguisher is an option and what follows.
  • Flooded Outlets: Outlets that were underwater or soaked should stay off until inspected. Learn what to leave alone, what a technician checks first, and how to describe it.

Need to discuss an electrical concern or planned project?

Request service
Call (954) 481-0910