Safety first: when to call 911 before anything else
Before sorting out who is responsible, check for danger. If you see smoke, flames, or sparks, smell burning or hot plastic, hear popping or loud buzzing from a panel or outlet, or someone has been shocked, leave the unit, close the door behind you, and call 911. If the building has a fire alarm, use it. Do not go back for belongings or pets. A fire in one unit can spread quickly through shared walls and ceilings, and responders need clear access.
If there is water on the floor near outlets, an appliance, or the panel, stay out of the water. Do not touch electrical equipment while standing in it. Leave the area and call for help. A leak from a unit above is a common cause of electrical problems in condominiums, because water runs down walls and ceilings and enters fixtures, outlets, and sometimes the panel. Treat wet electrical equipment as unsafe until an electrician has checked it.
If none of those things apply and you are simply in the dark, you have time to sort the problem. That is the purpose of the rest of this page. Do not try to open the panel cover or any meter socket. Do not take apart outlets or fixtures. The steps below involve only looking, listening, and flipping breaker handles with a dry hand and dry floor, and only where it is safe.

Step one: is the whole building or neighborhood dark
Look out of a window and into the corridor. Are the street lights on? Are neighboring buildings lit? Are the corridor lights on? If everything around you is dark, the likely cause is a utility outage or a building-wide failure, and nothing inside your unit will fix it. Call the utility's outage line, or use its outage reporting tools, and check whether management has posted a notice.
If the corridor is lit and neighbors have power, the problem is more likely local. It may be inside your unit, in your meter or disconnect, or in the feeder that serves your line of units. Ask a neighbor directly above, below, or beside you. If several units in a vertical line lost power, the problem is probably in a riser or in the meter stack, which is the association's responsibility. If only yours is out, it points toward your unit or its own supply.
Do not assume that a quiet building means no problem. Many outages are reported by the first person to notice, and managers rely on residents. Tell management what you found, even if you are not sure of the cause. A quick message that says what is out and what is not can save time for everyone.
Step two: look at your own panel from a safe position
Most units have a panel inside, in a closet, hallway, or utility area. If it is safe and dry, open the panel door only, not the inner cover, and look at the breakers. A tripped breaker usually sits in a middle position or shows a colored indicator. Look for a main breaker at the top, and for any that has moved. Note what you see. Do not touch if you smell burning, see water, or hear buzzing.
If the main breaker has tripped, you can try to reset it once by pushing it fully to off and then to on, standing to one side, with a dry hand. If it holds, note what was running when it tripped. If it trips again, stop. A breaker that trips repeatedly is protecting the wiring from a fault or an overload, and forcing it is dangerous. Call an electrician and tell them what you saw.
If individual circuit breakers are tripped, reset each one once in the same way. If one trips immediately, leave it off and note which circuit it is. Unplug devices on that circuit if you can do so safely. Do not tape a breaker in place, and do not replace a breaker with a larger one. If you cannot identify what is wrong, call. For help reading what a tripped breaker means, see how to read a tripped breaker.
Step three: partial loss, such as half the unit or no 240 volt appliances
A unit that has power in some rooms but not others is a different case. Partial power can mean a single breaker has tripped, a ground fault device has tripped, or a connection has failed on one of the two legs that feed the unit. If half your outlets and lights are out, or if lights are dim or bright in an odd pattern, or the stove, dryer, or air conditioner has stopped working while some lights still work, there may be a problem with the supply to your unit or with a neutral connection.
Odd symptoms, such as lights that get brighter when something else turns on, are warning signs of a loose neutral or a failed leg. These faults can damage equipment quickly, and can cause heat at connections. Turn off sensitive electronics and large appliances, avoid using the affected circuits, and call. See loose neutral symptoms and half the house with no power.
The cause might be in your panel, which is yours to fix, or in the meter or feeder, which usually are not. A technician can tell the difference by measuring voltage at the panel and at the meter. Be aware that many condominium boundaries are drawn at or near the meter, so the electrician may need to involve management or the utility for part of the repair.
Who owns what: unit side and building side
Condominium documents set the boundary. In a typical arrangement, the association is responsible for the structure, the common areas, the main service, the risers and feeders, and the meter banks. The owner is responsible for the panel and wiring inside the unit and for fixtures and appliances. In some buildings the dividing line is the meter, in others the unit's main disconnect, in others the unit's wall. You need to read your declaration or ask management.
As a rough guide, if the fault is in your panel, your breakers, your outlets, your fixtures, or your appliances, it is yours. If it is in the meter room, the riser, the common corridor panels, or the feeder to your panel, it is typically the association's. If the utility's equipment has failed or the whole neighborhood is out, it is the utility's. These are generalities, and the documents control.
Insurance follows a similar pattern. Your own policy normally covers your unit's interior and contents, and the association's policy covers the building. If a failure causes damage, both may be involved. Keep records and photographs of damage and what you were told. See electrical damage and insurance documents for what to keep.
Calling management: what to say and what to ask
Call or message the manager or the building's emergency line. Give your unit number, a short description of what is out, and whether neighbors are affected. Say whether you saw or smelled anything unusual. Ask whether there is a known outage or work in the building, who handles electrical emergencies, and whether the manager will send someone to check the shared equipment.
If the association has a standard vendor for emergencies, ask whether you may use that vendor for unit problems or whether you should call your own. Ask whether you need to notify management before a contractor enters the building, and whether there are rules about working hours, parking, insurance certificates, or elevator reservations for contractors. Many condominiums require these, and a technician who arrives without them can be turned away.
Ask who will open the electrical room if the technician needs access to the meter or riser. Owners generally cannot open them. Ask whether the association will cover the cost of a call if the fault turns out to be in the shared equipment, and ask for the answer in writing if the amount could be significant. Keep a note of the time and name of everyone you speak with.
Calling the electrician: what to tell the dispatcher
If "Condo Unit Lost Power: Who Do You Call?" matches what is happening, call and describe it plainly: the room, the breaker, any burning smell or tripped circuit. We explain what the repair would involve before a visit is set.
Mention that you are in a condominium, and ask whether the visit may require building access to shared rooms. Tell the dispatcher whether management knows about the problem. If you are renting, say so and say who the owner is, since the owner may need to authorize repairs. See home or rental: which repair is yours.
Quotes are given by phone. Simple problems may be priced on the call, while more complicated problems need an on-site visit. There is a service call charge, which the dispatcher explains before sending anyone. Ask how the visit will work, and have the unit access arranged. For a more general list, see what to tell the electrician dispatcher.
Common causes in condominium units
Condominiums have patterns of trouble. Water leaks from a unit above can run into fixtures and outlets and trip ground fault protection. Older buildings may have panels from an earlier era with breakers that have worn out or are no longer available. Air conditioners and kitchens added over the years can overload circuits. Balcony outlets exposed to weather and salt air often corrode. In some older buildings, aluminum branch wiring was used, and connections can loosen over time.
High rise units may have panels that are accessed by the building manager, or meters in a central room, so even simple checks require coordination. Units near the coast see more corrosion. Units near the top of a building may have more frequent flickers from wind-induced movement of rooftop equipment. These are not everyday problems, but they shape what a technician looks for.
Appliances are another cause. A failing dryer, a window air conditioner on a shared circuit, or a space heater can trip a breaker. Unplug anything large from the affected circuit before resetting. If the breaker holds, plug items back in one at a time to identify the culprit. A device that trips the breaker repeatedly should not be used until it has been checked.
Three examples of sorting the problem
Example one: your unit goes dark at dinner time, the corridor is lit, and the neighbor reports normal power. You open your panel door and find the main breaker in the middle position. One reset holds, and the lights return. You note that the oven and the dryer were both running. That points to an overload from heavy appliances, which is a unit-side matter. If it happens again, an electrician can check the main breaker and the connections.
Example two: you and the units directly above and below you lose power at once, while the rest of the floor is fine. Your breakers are all on. That points to a riser or a feeder that serves your line, and the manager should be told right away so that the association's electrician can look at the shared equipment. Do not go looking for the room yourself.
Example three: your whole building is dark, and so is the street. The utility's outline of the outage shows a broad area affected. Nothing you do in the unit will help. Keep refrigerator doors closed, unplug sensitive electronics so that surges on restoration do not harm them, and wait for the utility. If power returns and something seems wrong, such as lights that are far too bright or dim, switch off large appliances and call.
These examples are simple, but they show the habit that works: look at the scope first, then your own panel, then call the right party. Resist the urge to fix everything at once.
What not to do in a condo power loss
Do not open the meter socket or the building's electrical room. Do not remove seals. Do not attempt to bypass a meter, a disconnect, or a breaker. Do not run an extension cord from a neighbor's unit across a corridor or through a door, since it is a trip hazard and a fire risk and may violate building rules. Do not use a generator inside your unit or on a balcony. Carbon monoxide kills.
Do not use a gas stove to heat a space, and do not use candles unattended. Do not go into an electrical room to look for the problem. Do not tape or wedge breakers. Do not allow an unknown person who says they are an electrician into the building without checking with management.
Do not assume that the problem will fix itself. A problem that appears minor, such as a flickering light, can be an early sign of a loose connection. Report it. See what never to do in an electrical emergency.
After the repair: record keeping and follow-up
When the problem has been resolved, ask the technician what they found and where. Ask whether it was on the unit side or the building side, and ask for a written note. If the problem was in shared equipment, share the note with management. If it was in your unit, keep it with your records. Take photographs of what was repaired, if you can.
If damage occurred, such as to appliances or electronics, document it with photographs, receipts, and notes about when it happened. Contact your insurer and the association as needed. See appliance and electronics damage after an event.
Finally, label your panel. A clear label for each breaker saves time and reduces the risk of guessing during the next emergency. When you are ready to describe your situation, or if you need help sorting the problem now, call and a dispatcher will walk through it with you.
Questions people ask
My condo lost power but the neighbors have it. What should I check first?
If there is no smoke, burning smell, water, or buzzing, look at your own panel from a safe position for a tripped main or circuit breaker. Reset a tripped breaker once. If it trips again or nothing is tripped, call an electrician, and let management know. The problem may be in your unit, your meter, or a feeder.
Who pays if the problem is in the building's equipment?
Usually the association handles repairs to the main service, risers, meter banks, and common equipment, while the owner handles the unit panel and wiring beyond it. The declaration controls, and some buildings place the boundary elsewhere. Ask management in writing, and keep the electrician's findings.
Can I hire my own electrician for a problem in the unit?
Often yes, but check the rules. Many associations require notice, insurance certificates, and scheduling for contractors, and some require use of approved vendors. Shared rooms can only be opened by authorized people. Ask management before the technician comes, so access is arranged and they are not turned away.
Several units in a line lost power. Whose problem is that?
That pattern usually points to a riser, a feeder, or a meter stack, which are generally the association's. Tell management right away, and do not open shared rooms. If there is any smoke, burning smell, or water near electrical equipment, call 911 first. The electrician can then trace the fault.
The lights flicker or get brighter when the air conditioner starts. Is that urgent?
It can be. Lights that change brightness with load can indicate a loose neutral or a poor connection, which can damage equipment and create heat. Reduce use of large appliances and call an electrician to test it. If you smell burning or see sparks, leave and call 911 first.
Can an electrician give a price before coming to my condo?
Quotes are given by phone. Simple problems may be priced on the call, while complicated jobs need an on-site visit first. There is a service call charge, explained before anyone is sent. Have access to the unit and any shared rooms arranged so the visit is not wasted.
If "Condo Unit Lost Power: Who Do You Call?" matches what is happening, call and describe it plainly: the room, the breaker, any burning smell or tripped circuit. We explain what the repair would involve before a visit is set.
Related pages
- Condo Emergency: Board members and managers: a call order for condo electrical emergencies, who handles shared rooms, what residents report, and what to document afterward.
- Electrical Room Risk: Managers: what to watch for in condo meter stacks and riser rooms, which signs mean call 911, which mean call an electrician, and how to keep rooms safe.
- Common Area Outage: Corridor lights, stairwells, and elevators dark in a condo building? Life-safety steps, who handles what, and what managers should tell residents.
- Tenant and Landlord: Power out at a leased business space? Learn how responsibility is usually divided between tenant and landlord, and why the lease comes first.
- Whose Repair: General responsibility basics for owned homes, rentals, and condos, so you know who to notify and what to tell the dispatcher before an electrician is sent.
- Outage Records: What to record during a business power outage for managers, landlords and insurers: timelines, photos, losses and technician findings, with no coverage claims.
