First priorities: people, wires, and fire
Check that everyone is out of the damaged area and accounted for. If anyone is trapped or injured, call 911. Do not go back into a collapsed or unstable part of the house to retrieve belongings. A structure that has taken a tree impact can shift, and an energized wire inside it is an added danger that you cannot see.
Look from a safe distance for wires on or near the tree. Overhead lines may be tangled in the branches, resting on the roof, or lying on the ground. Treat every wire as live, even if the power seems to be out in the neighborhood, because lines can be re-energized without warning. Stay well back, keep children and pets away, and call 911 and the utility. Never touch a tree that is in contact with a wire, never try to move a branch off a line, and never use a ladder or pole near it.
If you smell smoke or burning, see sparks, hear buzzing from the roof, or notice flickering lights while the power is on, leave the building and call 911. A damaged conductor can arc inside a roof assembly, and a fire there can spread before it is visible from the ground.

- Trapped or injured people: call 911 immediately.
- Wires on the tree, roof or ground: stay back, call 911 and the utility.
- Smoke, sparks, buzzing or burning smell: leave and call 911.
- Do not enter a structurally unstable area to check the electrical system.
How a tree damages electrical systems
A falling tree does harm in several ways at once. The impact force stretches, pinches, and cuts cables that run through the attic and walls. Branches can pull on the service drop, the wires running from the utility pole to the house, and tear the mast or the weatherhead off the roof. Water gets into the damaged openings and reaches wiring that was dry.
Cables in attics are especially vulnerable. They are often stapled along rafters or run across joists, and when a roof is pushed down, rafters move and the cables are crushed or stretched. A cable that has been crushed may have a cracked outer sheath and damaged insulation on the conductors beneath. It might hold up for a while, then arc or short when current flows.
Fixtures and devices mounted in the damaged area are also at risk. Ceiling lights, exhaust fans, smoke alarms, and junction boxes can be torn loose from their mounting and left hanging on their wires. A loose connection can heat under load, and a pulled-out wire can touch metal or another conductor.
The service line at the roofline
The most serious electrical hazard after a tree strike is often where the utility's wires meet the house. At many South Florida homes, an overhead drop runs from a pole to a weatherhead on a mast or to the roofline, then down to the meter socket. A tree pushing on this assembly can bend the mast, pull the weatherhead off, rip the conductors out of the connection, or drag the drop toward the ground.
Those wires are energized from the utility side, and the voltage is high enough to kill. If the drop is sagging, torn, or touching the roof, a gutter, a fence, or the tree, stay far away. Do not try to lift or move it. Do not touch the mast, the meter, or the conduit. Keep everyone out of the yard near the damage and call 911 and the utility.
The utility handles its own lines and the connection point, and an electrician handles the customer side: the mast, the weatherhead, the conduit, the meter socket, and the wiring from there into the panel. The page on a tree on the service line explains the split in detail, and the page on storm-damaged meter and mast explains what needs repair before reconnection.
Shutting off power: when and how
If the house still has power and you believe wiring was damaged, turning off the main breaker can reduce the hazard inside. Do it only if the panel is easy to reach, dry, undamaged, and away from the damaged area, and if you can do it without entering an unsafe space. Stand to the side, use a dry hand, and move the main handle firmly to off.
If the panel is in the damaged part of the house, wet, or showing damage, do not go near it. Leave the building and call 911 and the utility, who can disconnect service at the pole or the meter. Do not pull the meter yourself, and do not cut any wire.
Remember that turning off the main stops the power inside the house but does not de-energize the service conductors above the main breaker and the wires outside. They remain live from the utility side. See the page on when it is safe to use the main breaker for more guidance on this.
What not to do after a tree impact
Do not go into the attic or crawl into the damaged area to inspect the wiring. Cables may be exposed, insulation may be wet, and the structure may be weakened. Do not cut or remove tree limbs that are touching wiring, the mast, or the roof edge. Do not climb onto the roof to cover the damage while there are energized lines nearby.
Do not turn power back on after the utility restores it without checking the house. Restored voltage can energize a damaged cable, and a damaged cable can start a fire. If there was any sign of damage inside, leave the main breaker off until a qualified electrician has inspected.
Do not run extension cords through the damaged area or use a generator connected to the house. If you need temporary power, use a generator outdoors, well away from the house, with cords run directly to what you need. See generator safety after a hurricane for the rules, and never connect one to the house wiring through an outlet.
Damage that is easy to miss
Many problems after a tree impact are not visible. A crushed cable looks fine from the outside if the sheath is intact. A pulled connection inside a junction box leaves no mark on the ceiling. A cable that has been stretched may have thinned conductors that heat under load. A cracked weatherhead may let water into the conduit and run down to the meter socket and the panel.
Water is a common secret. A roof opening during a storm lets rain into the attic, onto insulation, and down into ceiling fixtures and wall cavities. Wet insulation next to wiring can sit for days. When power is restored, current can find a path through the wet material, producing tripping breakers, buzzing, or a hot spot.
The signs to watch include ceiling stains, a wet fixture, a light that flickers, an outlet that is warm or stopped working, breakers that trip, a musty or burning odor, and noise from the walls. If you see any of these in a part of the house near the damage, treat the circuit as unsafe and tell the technician.
What an electrician inspects
The technician starts outside, looking at the mast, the weatherhead, the service drop connection, the meter socket and the conduit, noting what must be repaired or replaced before the utility can reconnect. They check how the damage affects the grounding conductor and the connection to the ground rod.
Inside, they test the panel for water, damage and proper voltage, and they check circuits near the impact. Circuits that run through the damaged area are tested for insulation resistance and continuity. Damaged fixtures, boxes and cables are identified, and where wiring runs through the damaged section of the roof or wall, the technician may need access from the attic or from below.
The technician then explains what is safe to energize, what must stay off, and what repairs are needed. Some work, such as replacing a weatherhead or a damaged fixture, can be done on the visit. Other work, such as rewiring a damaged section, may need a second visit or coordination with the roofer or the contractor who is repairing the structure.
Typical scenarios after a tree impact
Scenario one: a limb punches through the roof above a bedroom, and the ceiling light and the smoke alarm in that room stop working. The cable feeding them was likely pinched or torn in the attic, and the circuit may still be connected back at the panel. Leave that breaker off, keep the room closed, and tell the technician exactly which fixtures went dark.
Scenario two: the tree lands on the carport or the side of the house, and the meter and mast lean outward. Lights are still on. This is the situation to treat with the most caution, because the service conductors are stressed and may be close to pulling loose. Keep everyone away from that side of the house and call 911 and the utility.
Scenario three: a large branch falls on a detached garage or shed that has its own subpanel. The feeder to that building runs underground or overhead from the main house, and the impact may have damaged the conduit, the wire or the disconnect. Even if the main house looks fine, that feeder can be energized and damaged. Shut the feeder breaker at the main panel if it is safe to do so, and have the run inspected.
In every scenario, the principle is the same: protect people first, keep away from anything that may be energized, and let a qualified electrician prove that the system is safe before it is used again.
Coordinating with roofers, tree services, and the utility
A tree on a house involves several trades, and the order matters. Tree removal crews should not work near energized lines until the utility has made them safe. Roofers should not work around a damaged service mast until the electrical situation is clear. An electrician often needs to disconnect or restore service in the right sequence so that everyone can work safely.
Ask each contractor what they need from the others. The tree service may need the utility to de-energize or move a line. The roofer may need the mast detached and reattached. The electrician may need the roofer to restore weather protection before final repairs. The utility may require an inspection before it reconnects, and in many areas a permit is needed for the mast and meter work.
Keep a simple record of who did what and when. Photograph the damage before anything is moved, and photograph the repairs. The page on the power company disconnect and reconnect process explains how the utility side usually works.
Insurance and documentation
Photograph the tree, the damage to the roof and walls, the service line and mast, and any visible electrical damage, from a safe distance. Do not move the tree before taking photos if it is safe to wait. Write down the time of the event, who you called, and what you were told.
Ask the electrician for written findings, including what was damaged, what was repaired, and what remains to be done. An adjuster will often ask for this. The guide on electrical damage and insurance documents lists what to gather.
Keep damaged parts if possible, such as a bent mast or a failed fixture, until the claim is settled. When you are ready to arrange the inspection, call and tell the dispatcher about the tree, any wires involved, and what you can see. Ask about the service call charge and scheduling. Quotes for repairs come after the findings are explained, and a larger job needs an on-site visit. If you see smoke, sparks or a downed line, call 911 first.
Questions people ask
Is it safe to go into the attic to check wiring after a tree hit?
No. The structure may be weakened, cables may be crushed or exposed, and wet insulation next to wiring is a hazard. Stay out of the damaged area and have a qualified electrician inspect. If you smell smoke or burning, leave the house and call 911 rather than looking for the source.
A wire is touching the tree on my house. What should I do?
Stay far back and treat the wire as live. Keep people and pets away, do not touch the tree or any branch contacting it, and do not try to move the wire. Call 911 and the utility. A wire can be energized even if the power in the neighborhood seems to be out.
Who fixes the mast and weatherhead if the tree tore them off?
An electrician repairs the customer-side equipment, which includes the mast, weatherhead, conduit and meter socket. The utility handles its own lines and the connection point, and it generally will not reconnect until the customer-side equipment is repaired. Often both must be coordinated, and a permit may be needed.
Can I turn the power back on once the utility restores it?
Not if the house was damaged. Restored voltage can energize a crushed or exposed cable. Leave the main breaker off until a qualified electrician has inspected the damaged areas and the service equipment. If there was no damage inside, still watch for tripping breakers or odd smells after restoration.
What damage is easy to miss after a tree impact?
Crushed cables with an intact sheath, pulled connections inside junction boxes, stretched conductors, torn fixtures hanging on their wires, and water that has soaked insulation next to wiring. These do not always show on the surface. Testing for insulation resistance and continuity is how a technician finds them.
How should I prepare when I call an electrician?
Give your address and a callback number. Say whether wires are down, whether there is smoke or a burning smell, whether the main breaker is on or off, and what part of the house was hit. Ask about the service call charge and scheduling. Larger jobs need an on-site visit before a quote.
About "A Tree Fell on the House: Electrical Hazards": call and give us the details, and we will explain what is safe to do while you wait and what the visit would cover. Jobs that cannot be quoted blind need a look on site.
Related pages
- Tree on Line: A tree pulled down the service line to your house. Learn who handles mast, drop and conduit damage, what to avoid, and how to coordinate the repair.
- Mast and Meter: Why damaged meter sockets, masts and weatherheads must be repaired by an electrician before the utility reconnects, and how the process usually works.
- Downed Wire: A wire on the ground may be live even if it is silent. Learn how to keep a safe distance, call 911 and the utility, and what never to do near a fallen line.
- Line on Tree: A power line resting on a tree, fence or roof can energize it. Learn the hazards, the correct call order, and what to avoid until the utility makes it safe.
- Wet Attic Lights: A roof leak can send water along wiring into ceiling lights. Learn what is safe to do, what to leave alone, and how an electrician triages a wet ceiling.
- Flood and Wiring: How floodwater damages wiring, breakers, outlets and panels: corrosion, contamination, trapped moisture, and why wet devices are replaced instead of dried.
