Electrical help for homes and businessesRequest service
Emergency ElectricianCall (954) 481-0910
Emergency Electrician technician using an infrared camera to inspect a residential electrical panel

Safety and Guides

Electrical Emergencies in Mobile and Manufactured Homes

Mobile and manufactured homes are wired differently from site-built houses, and responsibility for the wiring is often split between the resident, the park and the utility. This guide explains the parts, the warning signs, the first steps and who to call.

How a manufactured home is fed and why it matters

A manufactured or mobile home receives power through a chain of equipment that is different from a typical house. In a park or on a lot, the utility connection ends at a meter and a service pedestal or pole. From there, a feeder cable or set of conductors runs to the home, and inside the home a distribution panel feeds the circuits. In some installations the service equipment is at a pedestal near the lot line, with a main breaker there, and the panel in the home is a distribution panel only.

That arrangement matters in an emergency. The breaker you see inside the home may not be the main breaker for the whole supply, and shutting off everything inside may still leave the feeder energized outside. The feeder itself, whether it is a cable on the surface, a line run overhead or a conduit under the home, may be exposed to weather, animals and mowers in ways that wiring in a block house is not.

Many South Florida manufactured homes are in communities with shared infrastructure, where the park owns the pedestals and underground distribution and the resident owns the home and its internal wiring. Others sit on private lots with their own meters and service equipment. Understanding which arrangement you have is the first step in knowing who to call, and the sections below set out how responsibility often divides.

Emergency Electrician technician installing a pendant light in a bright coastal home

The parts you may see: pedestal, feeder, panel and underbelly

The pedestal or service post is the point where the supply is connected to the home. It may contain a meter, a main breaker, a receptacle and a connection for the feeder. Pedestals sit outdoors in sun, rain, sprinkler spray and salt air, and their covers, seals and terminals take a lot of wear. Look for cracked covers, rust, missing screws, insect nests and signs of heat without touching anything.

The feeder is the cable or conductors between the pedestal and the home. It may be buried, run overhead or run across the surface. Surface runs can be damaged by mowers and vehicles, buried runs by digging, and overhead runs by trees and storms. A feeder with damaged insulation is a serious hazard, and a feeder that has been spliced or patched deserves inspection.

Inside the home, a panel feeds branch circuits. Under the home, in the area often called the belly, lie wiring runs, junction boxes and sometimes ducts and plumbing. Animals, moisture and age affect the insulation there. Wiring in the belly or in the ceiling may be hard to reach and hard to see, which is why a fault in these areas can progress unnoticed. The page on older home electrical red flags lists signs that apply to older manufactured homes as well.

Warning signs that call for immediate action

Most warning signs are the same as in any home, but a few carry extra weight in a manufactured home. A tingle or shock from the metal skin, the frame, a metal step or a handrail is serious, because the metal body of the home is meant to be at the same voltage as the ground. A tingle usually means a fault in the grounding, a neutral problem or an energized conductor touching metal, and it needs immediate attention.

Other signs include a burning smell from the pedestal or panel, lights that flicker, dim or surge, a tripped main that will not reset, outlets that are warm or discolored, a buzzing from the pedestal, a hot or damaged feeder, sparks at the meter, water in the pedestal or panel and appliances that act oddly. Any sign accompanied by smoke or flame is a 911 call.

  • Tingle or shock from the metal skin, steps, rails or an appliance
  • Burning smell near the pedestal, panel, belly or an outlet
  • Sparks, buzzing or heat at the pedestal or meter
  • Lights that flicker, surge or are very bright or very dim
  • A feeder cable that is cut, melted, exposed or sagging
  • Water in the pedestal, panel or under the home around wiring
  • Half the outlets dead, or appliances that run strangely

What to do first

If there is fire, smoke, flame, a person shocked or sparking at the pedestal, call 911, get everyone out of the home and wait at a safe distance. Manufactured homes can burn quickly, and there is little time to hesitate. Do not go back in for belongings. Tell the dispatcher it is a manufactured home and, if you know, whether the fire may involve the pedestal.

If you feel a tingle from metal parts, stop touching them, keep others away and do not use water or damp hands near the area. Move everyone out of the home if the tingle is anywhere other than a single appliance and call. If the tingle came from a single appliance, unplug it only if the plug is not hot and the area is dry, and set the appliance aside.

If there is no immediate danger but you suspect a fault, switch off the affected circuit at the panel inside if it is dry and easy to reach, and note what you saw. Do not open the pedestal, do not touch the feeder and do not try to splice or repair a damaged cable. The pages on what never to do in an electrical emergency and what to do when a person is shocked at home describe the first steps in detail.

Who is responsible for which part

Responsibility depends on the park rules, the lease and whether the lot is owned or rented. In many parks, the utility owns the service up to the meter, the park owns the pedestal and the underground distribution within the community, and the resident owns the feeder from the pedestal to the home and the wiring inside. In others, the park owns the feeder as well. On a private lot, the owner owns everything beyond the utility meter.

You do not need to resolve this to make a hazard safe. A qualified technician can make a dangerous condition safe, and the question of who pays can be sorted afterward. What you should do is report the problem promptly to the park management and keep a written record. If the pedestal or feeder is damaged, management may need to arrange the repair or coordinate with the utility.

If your power is out because the utility has disconnected service, or because equipment on the utility side is damaged, the utility is the right party to call. The page on utility or electrician: who fixes what explains the dividing line, and the page on home or rental: which repair is yours covers renters.

Aluminum wiring, older branch circuits and add-ons

Many manufactured homes built in earlier decades used aluminum branch wiring, which behaves differently from copper. Aluminum expands and contracts more with temperature, and its connections can loosen over time and corrode, leading to heat at outlets, switches and breakers. A warm outlet, a flickering light or a smell of hot plastic in a home with aluminum wiring is a warning that should be taken seriously. The page on urgent aluminum wiring failure describes what the work involves.

Add-ons are another source of trouble. Porches, carports, sheds, additions and outdoor outlets added over the years may be fed by extension cords, undersized cable or taps from existing circuits. A long extension cord feeding a refrigerator or air conditioner is a common sight and a common cause of overheating. Space heaters and window air conditioners on shared circuits also strain old wiring.

If you see cords running through doors or windows to feed equipment, treat it as a sign that the home's wiring needs attention, not a permanent arrangement. A technician can recommend dedicated circuits where they are needed. The guide on extension cords and power strips limits explains why they are not a substitute for wiring.

Storms, flooding and wind

Manufactured homes in South Florida face hurricane winds, flooding and heavy rain, and the electrical system is one of the first parts to suffer. Wind can bend a service mast or tear down an overhead feeder. Flooding can reach pedestals and the area under the home, soaking wiring and connections in the belly. Rain driven into a pedestal or panel can cause faults.

After a storm, do not touch downed lines, bent masts or damaged pedestals, and do not walk through water near any of them. Stay away from the home if you suspect it is energized by a damaged feeder. The pages on storm-damaged meter and mast and downed wire in the yard explain what to do.

Do not restore power to a home that has had water under it or in the panel until a qualified electrician has inspected the equipment. Saltwater is especially damaging. The page on flooded home electrical first steps sets out the order of decisions.

What the technician will check

On arrival, the technician will confirm that power is off where needed, and will usually start at the pedestal or service point. They will inspect the pedestal, the feeder, the connections and the protective devices, test voltage and grounding and look for heat damage, corrosion, water and animal damage. They will look at the panel inside the home, test circuits and check the neutral and grounding connections, which are critical in a manufactured home.

If a fault is suspected in the belly or ceiling, they may need access to those areas, which can require removing a panel or cover. They will check the connections at junction boxes, the condition of the wiring and any splices. If aluminum wiring is present, they will look at the connections at outlets and switches.

Repairs may be as simple as replacing a breaker or an outlet, or as involved as replacing a feeder, a pedestal component or a section of damaged wiring. Some work may require coordination with the park or the utility, and some may require permits. Complicated jobs need an on-site visit, and the service call charge is explained on the phone before dispatch. Quotes for simple jobs are given by phone.

What to have ready when you call

Tell the dispatcher that the home is a mobile or manufactured home, and say whether it is in a park or on a private lot. Describe what you saw, heard or smelled, whether anyone felt a tingle or shock, whether the main or any breaker tripped and whether neighbors are affected. Say whether the problem is at the pedestal, the feeder, the panel or inside the home, if you know.

Have the park management contact ready, and let them know a technician is coming, since access to the pedestal or the community may require their approval. Keep pets and children away from the pedestal and feeder. Clear a path to the panel and to the areas where the technician may need access.

If anything changes while you wait, such as smoke, flame, sparks or a louder buzz, call 911 and update the dispatcher. Otherwise, call now and describe what is happening, and the dispatcher will guide the next steps.

Questions people ask

I felt a tingle touching the metal step of my mobile home. What should I do?

Stop touching it, keep others away and treat it as an emergency. A tingle from the metal body usually means a grounding or neutral fault or an energized conductor touching metal. Move people away, call 911 if anyone is hurt or unwell, and call an electrician. Avoid wet ground and damp hands.

The breaker inside my home is off. Is the home fully shut off?

Not necessarily. In many manufactured homes, the main breaker is at the pedestal, and the panel inside is only a distribution panel. The feeder may remain energized. Do not touch the pedestal or feeder, and leave work on them to a qualified electrician.

Who fixes a damaged pedestal in a park?

It depends on the park's arrangement and the lease. The park often owns the pedestal and distribution, the resident the feeder and home wiring, and the utility the supply up to the meter. A technician can make a hazard safe first. Report the damage to management in writing and keep copies.

My home has aluminum wiring and an outlet is warm. Is that urgent?

A warm outlet is a warning of a loose or corroded connection, which is a known concern with aluminum wiring. Stop using the outlet, switch off the circuit if it is safe and call. Do not keep using it because it still works.

Can I run an extension cord to power a refrigerator or air conditioner?

A long cord feeding a large appliance can overheat and fail. It is a sign that the circuit is not meant for the load. Use it only as a short-term stopgap with a heavy-duty cord and check for warmth, and ask an electrician about a dedicated circuit.

How does pricing work for an emergency visit?

Quotes for simple jobs are given by phone. Complicated jobs need an on-site visit before a quote can be given. There is a service call charge, and it is explained on the phone before dispatch. This site lists no dollar amounts because each situation differs.

Talk to Emergency Electrician

If "Electrical Emergencies in Mobile and Manufactured Homes" matches what is happening, call and describe it plainly: the room, the breaker, any burning smell or tripped circuit. We explain what the repair would involve before a visit is set.

Related pages

  • Shock Victim: If someone was shocked at home, call 911 first and do not touch them while still energized. Learn the safe order of steps and the electrical check afterward.
  • Frayed Service Cable: Frayed, sagging or rubbed-through service cable at your house: how to tell utility lines from your own conductors, what to avoid and who to call first.
  • Aluminum Wiring Failure: Why older aluminum branch wiring can fail at outlets, switches and fixtures, the warning signs, and the stabilization options a technician may discuss.
  • Who Fixes What: Where utility equipment ends and customer equipment begins, in general terms, so you know whether to call the power company, an electrician, or 911 first.
  • Whose Repair: General responsibility basics for owned homes, rentals, and condos, so you know who to notify and what to tell the dispatcher before an electrician is sent.
  • Emergency Permits: How urgent electrical repairs still move through permits and inspections in South Florida, what usually needs one, and what to ask before work starts.

Skirting, crawl spaces and the hidden path of the feeder

In many mobile and manufactured homes, wiring and feeder connections run through spaces that are hard to see, such as beneath the floor or behind the skirting. These areas can collect moisture, attract pests and trap heat. A rodent chewing on insulation, or a dripping pipe above a junction, can create a hazard that never shows inside the living space until something trips or fails. For that reason, a visit often includes careful examination of the underside where it is safe to do so. Take your time describing it, and say so if you are unsure, because an honest I do not know is more useful than a confident guess.

Do not crawl under the home to investigate on your own, especially after rain or flooding. Water, damaged wiring and cramped spaces are a dangerous combination, and snakes and insects are common in Florida. If you suspect a problem there, such as a wet area, a chewed cable or a smell from beneath, keep the area clear and describe what you noticed when you call. Any work in that space is done with the power isolated first. If anyone in the home depends on powered medical equipment, mention that early so it can be considered when the plan is made.

Ask the technician what was found in the hidden spaces and whether there are other conditions to watch for. Hidden damage may not require immediate repair but can matter in the future. Skirting repairs, vapor barriers and drainage around the home may also influence how long wiring stays dry. If someone else owns the land or runs the park, find out who handles those parts and share what the technician reports with them. Florida humidity, salt air and summer storms add stress to electrical parts, so conditions that seem minor elsewhere can matter more here.

Wind, tie-downs and the strain on the connection to the home

Manufactured homes sit on supports and are anchored against wind, and in a strong storm the structure can shift slightly. That movement matters electrically, because the connection between the home and its power source needs enough slack and support to tolerate it. A strained connection can loosen over time, and a loose connection can heat up. After a major wind event, visible bending, pulled cables or a gap near where wiring enters the home deserve attention. Keep children and pets away from the area while you wait, and avoid touching anything that feels warm, damp or looks discolored.

If you notice any of these after a storm, leave them alone. Do not push, pull or try to reseat anything, and do not tape over a connection. Keep people and pets away from anything that looks damaged, and avoid standing in wet ground near it. If you can do so safely, take a photo from a distance and note when you noticed it. This helps whoever responds understand what changed. Write down what you noticed, in the order you noticed it, because memory fades quickly once the situation becomes stressful.

A technician will look at whether the connection is secure, whether the surrounding support is stable, and whether moisture entered. Because some parts belong to the utility or the park rather than the resident, the first conversation may involve working out who is responsible for what. We explain that division and the scope of any work before it begins, so you know who needs to be contacted and what will be handled in which order. Ask for anything you do not understand to be explained in plain words, since you should be comfortable with the plan before work begins.

Need to discuss an electrical concern or planned project?

Request service
Call (954) 481-0910