Triage: separate the electrical hazard from the dark yard
A dark exterior raises two worries at once: whether the wiring is dangerous, and whether the property is safe at night. Handle the electrical hazard first. If you see sparks, smoke, flame, a melted fixture or a burning smell from an outdoor light, call 911 and keep away. If a fixture is hanging by its wires, if water is running out of a light or a box, or if anyone received a tingle or shock from a light pole, a fixture or a metal fence near them, treat it as an emergency and stay clear.
If there is no sign of fire or shock, the problem is urgent but not an immediate danger to life. Leave the circuit switched off if you can identify it, and do not attempt to work on a wet fixture in the rain. Do not touch a fixture with wet hands or while standing in water or on wet ground. Never use a metal ladder near overhead wires or a service mast.
For personal safety while the lights are out, use battery lanterns or flashlights, keep exterior doors locked, and consider contacting neighbors or the property manager. If you feel threatened, call the police. Do not run an extension cord across a wet yard to power lamps or a floodlight as a workaround. Our page on outdoor outlets and yard electrical safety explains why cords outside need extra care.

Why exterior lighting fails so often
Moisture is the main reason. South Florida rain, high humidity and sprinkler overspray all reach outdoor fixtures and junction boxes. A fixture that is not sealed, or whose gasket has aged and cracked, lets water into the housing. Water on terminals causes corrosion, leakage and shorts. A fixture may work in dry weather and fail every time it rains, which is a classic sign of a moisture problem.
Sun and heat age the plastic and rubber parts. Gaskets harden and crack, plastic lenses yellow and become brittle, and cable jackets crack. Salt air near the coast speeds corrosion of metal parts, screws and terminals, and fixtures near the water often have shorter lives. Insects, ants, wasps, geckos and spiders get into fixtures and boxes, and nests can bridge terminals or block heat from lamps.
Electrical causes include failed lamps and drivers. Many modern outdoor fixtures use LED modules with drivers, and the driver, a small power supply, can fail from heat or moisture. Photocells that turn lights on at dusk can fail and leave lights on all day or off all night. Motion sensors can fail or be triggered constantly by animals and plants. Timers and switches can fail too.
Wiring faults add to the list. Outdoor cable can be cut by lawn equipment or damaged by roots and soil movement. Splices made in the ground with ordinary connectors fail. And GFCI protection, required on many outdoor circuits, trips when it senses leakage, so a dead outdoor circuit is often a tripped GFCI, as discussed below.
Check the safe basics first
Before calling, there are a few safe checks you can make from the ground. Look at whether the lights are out across the whole property, or just one or two fixtures. A whole-property outage points to a tripped breaker, a tripped GFCI, a failed photocell or timer, or a dead circuit. One fixture dark suggests a lamp, driver or fixture fault.
Check the indoor panel for a tripped breaker, and note whether any outdoor outlets in a garage, porch or patio are also dead. Find any GFCI receptacles, which have test and reset buttons, in garages, bathrooms, kitchens and outdoors. A tripped GFCI can switch off a whole chain of outdoor outlets and lights. Press reset once, firmly. If it holds, observe whether the lights work. If it trips again at once or on the next rain, leave it and call, because it is detecting leakage. Our page on a GFCI that will not reset explains what is happening.
Look at the photocell, a small dome on a fixture or a switch box, and whether the light is in a dark place or covered by a plant or a decoration. A dirty or covered photocell can make lights behave oddly. Check the light switch or timer inside.
Do not remove fixtures, open junction boxes or replace drivers yourself. Do not climb ladders in the dark or the rain. If the safe checks do not restore the lights, or if the breaker or GFCI trips again, stop, keep the circuit off, and call.
How a technician diagnoses an outdoor lighting failure
The technician starts with the symptoms and the conditions. When did it fail? Was it after rain, a storm, a power surge, or the use of a pressure washer or sprinklers? Does it fail only when wet? Which lights are affected? Are lights on the same circuit as outlets that work? This information narrows the search.
They check the protection at the source: the breaker, any GFCI device and the switch or timer. They test voltage at the first fixture to see whether the circuit is live. If power reaches the first fixture and not the next, the fault is in between. If no power reaches the first, the problem is upstream. This step-by-step approach follows the circuit outward until the break or fault is found.
At each fixture, they check the lamp, the driver or ballast, the wiring connections and the housing for water, corrosion and insects. They use an insulation resistance tester on isolated sections of the circuit to find leakage to ground, which is the usual cause of a GFCI that trips. For underground runs, they check for damage and moisture, and may use a tracer to locate the cable.
Our page on tracing a ground fault explains the method in more detail. The technician tells you what they found, and whether the fix is a lamp, a driver, a fixture, a box, a section of cable or a combination. Quotes are given only by phone, and complicated jobs need an on-site visit; there is a service call charge, explained before dispatch.
Repairs: fixtures, boxes, sealing and wiring
Repairs match the failure. A failed lamp or driver is replaced with one suited to the fixture. If the fixture's housing is corroded, cracked or full of water, replacement is usually better than repair, since a compromised housing will leak again. Replacement fixtures should be rated for wet locations where they are exposed to rain, and for damp locations when covered. The rating is marked on the fixture.
Junction boxes outdoors must be weatherproof, with gaskets and covers that seal, and with fittings that keep water out at cable entries. A box with a cracked cover or a missing gasket is replaced or repaired. Connections inside use listed connectors, and where moisture exposure is likely, sealed or gel-filled connectors are used. Connections made with ordinary tape and twist caps in a damp box are not acceptable.
Damaged outdoor cable is repaired or replaced following the same principles as indoors, with splices in accessible weatherproof boxes, and with cable types listed for the location. Underground cable that has been cut or has taken on water may need replacement, with correct burial depth and protection. Our page on repairing damaged wiring properly explains acceptable splicing. If the lights are low-voltage landscape lighting, the repair differs, as described on landscape lighting shorts.
After the repair, the technician checks that the GFCI trips and resets as designed, and that the photocell, timer or sensor works. They may adjust the sensor's aim and sensitivity so that it does not respond to animals or vegetation. They test the lights after dark if possible, or simulate darkness with the photocell covered.
Security lighting: sensors, coverage and reliability
Security lighting has its own concerns. A light that is out when you need it is a security gap, but a light that is poorly placed or aimed does little even when working. When repairing, a technician will consider whether the sensors are positioned to cover entrances, driveways and dark corners, and whether fixtures are mounted where they cannot be easily tampered with or reached from the ground by someone unauthorized.
Motion sensors have settings for sensitivity, range and duration. A sensor set too sensitive turns on for every cat or palm frond and wears out lamps, and one set too low misses people. Dusk-to-dawn photocells need to see the sky and not be shadowed by the fixture's own light, which would cause cycling. Wiring for security lighting should be on a dependable circuit, preferably not the same circuit as a likely overload such as a garage tool circuit.
Consider backup for critical lighting. Battery-backed lights and solar fixtures can provide some light when power is out, though they have limits. If you rely on exterior lighting for safety at a business, an entrance or a path, discuss with the technician how to keep the key spots lit. Our page on parking lot and pole light outages covers larger sites.
In HOAs and condominiums, exterior lighting on common property is typically the association's responsibility. Report outages to the association or manager promptly, in writing, and keep a record. A lit property is also a legal and insurance matter in some situations, so documentation helps.
Pool, patio and dock lighting: extra care near water
Lighting near pools, spas, fountains and docks needs extra care. Water and electricity are a dangerous combination, and the standards have strict rules for distances, bonding and protection around pools. Underwater pool lights and nearby fixtures are required to be protected by GFCI devices or to operate at low voltage from an approved transformer, depending on the type. A fault there can put current into the water.
If you notice tingling in a pool, a pool light that flickers or trips a breaker, or a fixture near the water that is cracked or wet inside, get everyone out of the water and stay out until it has been checked. Do not touch metal fittings, ladders, rails or pool equipment while someone is in the water. If anyone has been shocked, call 911 first. Our guide on pool equipment tripping power describes related warning signs.
Patio and lanai lighting under covered structures is often on circuits shared with ceiling fans and outlets. A fixture there can fail because of humidity and insects, and wet-location fixtures may be required. Docks and seawalls face salt, tidal movement and frequent hurricanes, and equipment there should be corrosion-resistant and protected.
Repairs near water should be done by a qualified electrician who knows the rules. Do not replace a pool light or work on pool wiring yourself. The risk of electric shock drowning is real, and prevention depends on correct bonding, grounding and GFCI protection, all of which the technician will verify.
After storms and floods: what to do with outdoor lights
Storms are hard on outdoor lighting. Wind can pull fixtures off walls, snap poles and break cable. Rain driven into fixtures can short them. Flooding can reach low fixtures, in-ground lights, outdoor outlets, transformers and underground cable, and floodwater, particularly salt water, leaves corrosive residue.
After a storm, treat all outdoor electrical equipment as suspect until checked. Do not touch fallen fixtures, wires on the ground or poles lying on fences. Stay out of standing water that could be energized. If wires from the utility are down, call 911 and the utility and keep well clear. Our guide on a downed wire in the yard covers that situation.
Do not re-energize circuits that serve flooded or soaked outdoor lighting. Keep breakers off until a technician has tested the cable and replaced wet equipment. Low fixtures and in-ground lights that have been submerged are typically replaced. Our page on pool and spa electrical safety after a flood covers related equipment.
Documenting damage with photographs from a safe distance helps with insurance claims, and the technician's written notes add detail. If you have storm shutters, remember that fixtures behind them can be damaged by trapped moisture, and that wiring to shutters, gates and lights can be damaged by wind.
Calling for help and keeping outdoor lighting reliable
When you call, describe what is happening: which lights are out, whether it started after rain or a storm, whether a breaker or GFCI tripped, and whether you smelled burning or saw damage. Say whether there is a pool or water nearby, and whether you feel unsafe because of the darkness. If anyone received a shock or tingle, say so first.
Quotes are given only by phone, and complicated jobs need an on-site visit. There is a service call charge, and it is explained on the phone before dispatch. Ask what the technician will check, whether the repair can be done in one visit, and whether parts may need to be ordered. Our guide on what to tell the electrician dispatcher lists helpful details.
To keep lighting reliable, use fixtures rated for wet locations, replace cracked covers and gaskets promptly, and use in-use covers on outdoor outlets. Test GFCI devices monthly. Keep sprinklers from spraying fixtures. Trim plants back from sensors and lights, and clean photocells. Do not use indoor-rated fixtures or ordinary extension cords outside.
If your outdoor or security lights are out, or you have seen any warning sign described here, call and describe the situation. A dispatcher can tell you what to do right now, explain the call charge in advance, and arrange for a technician to find the cause and restore safe lighting.
Questions people ask
Why do my outdoor lights stop working after rain?
Water has likely entered a fixture, box or connection and is causing leakage that trips a GFCI or breaker, or corroding terminals. A worn gasket, cracked cover or poor seal is a common cause. Keep the circuit off if it keeps tripping, avoid touching wet fixtures, and have the moisture source and wiring checked.
Is a GFCI that trips outdoors dangerous?
The tripping itself is the device protecting you. It means current is leaking to ground, perhaps through water or a damaged fixture. Do not keep resetting it, and do not replace it with an ordinary outlet. Leave it off, stay away from wet equipment, and have the circuit tested so the leak is found and repaired.
Can I swap a failed fixture myself?
Only if you are qualified and can confirm the circuit is off with a proper tester. Outdoor work adds wet conditions, ladders and weatherproofing requirements, and mistakes can leave water entering the fixture later. Near pools, never do it yourself. For most owners, calling a qualified electrician is the safer choice.
My security light stays on all day. What is wrong?
Common causes are a failed photocell, a sensor stuck on, a fixture whose sensor sees its own light, or a switch or timer fault. It is usually not dangerous but wastes lamp life. If the fixture is hot, discolored or smells burned, switch it off and have it checked sooner.
Are low-voltage landscape lights safer to work on?
They run at lower voltage but are still fed from a transformer connected to household power, and faults on the primary side or at the transformer can be dangerous. Shorts in low-voltage runs can overheat wire and the transformer. Turn off the transformer and have it checked if lights are out or the transformer is hot or buzzing.
What should I do if lights near my pool flicker or trip the breaker?
Get everyone out of the water and stay out. Do not touch metal fittings, ladders or equipment. Turn off pool power if you can do so safely from a dry location. If anyone felt a tingle or shock, call 911 first. Then call an electrician to test the bonding, grounding and protective devices before the pool is used.
If "Urgent Outdoor Lighting Repair" matches what is happening, call and describe it plainly: the room, the breaker, any burning smell or tripped circuit. We explain what the repair would involve before a visit is set.
Related pages
- Landscape Short: A burned landscape lighting transformer or shorted low-voltage run can hide a bigger problem. Learn the triage steps and when a technician should check it.
- Ground Fault Tracing: How a technician isolates a ground fault with testing rather than guesswork, what trips a breaker or GFCI, and what you can safely do while you wait.
- GFCI Won't Reset: A GFCI that will not reset means a fault or a failed device. Learn what safe checks you can do, what to avoid, and how to describe the problem by phone.
- Outdoor Outlets: Outdoor outlet covers, GFCI protection, sprinklers and tools in wet South Florida yards: what to look for, what to avoid and when to call a technician.
- GFCI/AFCI Fix: GFCI and AFCI devices trip for real reasons. Learn what repeated trips mean, why bypassing them is dangerous, and how a technician traces the fault behind them.
- Knob-and-Tube Hazard: What to do when old knob-and-tube wiring is found damaged, buried in insulation or overheated, how technicians assess it, and how replacement is decided.
