Start with safety, then with the lights
A parking lot with dead lights is a different problem from a hallway with a dead bulb. The area is open to the public, it has moving vehicles, and customers or employees may be leaving after dark. Before anyone thinks about the electrical cause, think about the people on the property. If someone is hurt, if a pole is down, if a wire is lying on the pavement, or if anything is smoking, sparking or burning, call 911 first. Those are emergencies for the fire department and police, and the electrician comes after the scene is safe.
If the situation is only darkness, the practical question is how to keep people safe tonight. A manager can close the lot or a section of it, steer customers to a lit entrance, ask staff to walk people to their vehicles, and park a vehicle with headlights on at the darkest spot. None of that fixes the electrical fault, but it reduces the chance of a fall, a collision or a crime of opportunity while a technician is on the way.
It also helps to decide early whether the outage is local or widespread. If the whole building and the neighboring businesses are dark, the problem is probably the utility, and the number to call is the power company's outage line. If the building is lit and only the lot is dark, the fault is on the private side of the meter, and that is where an electrician can help.

- Anyone hurt, a pole knocked over, a wire on the ground, smoke or flames: call 911 first.
- Keep people and vehicles away from any pole that is leaning, cracked or damaged, and from the ground around it.
- Do not touch fixtures, poles, pull boxes or any wire, even if the power looks off.
- Block off the dark area if needed and direct people to lit walkways.
- Note whether the building itself has power, since that points to the utility or to a private fault.
How parking lot lighting is usually wired
Most commercial lot lighting follows a similar pattern even when the property looks different. Power comes from the building's main service or from a dedicated panel, passes through a contactor or a timer, and then runs outdoors in conduit, often underground, to a string of poles. Each pole has a fixture on top, and inside the base of the pole there is a small handhole or access door where the supply wires are connected to the fixture wiring, usually with a fuse or a disconnect.
Control is usually handled by a photocell, a small sensor that senses daylight and tells the system when to turn on at dusk and off at dawn. Some properties use a time clock or a building automation system instead, and some use both with a manual bypass. The photocell may be on a single pole, on the building, or built into each fixture. Where one photocell controls many poles through a contactor, a single failed sensor can leave the whole lot dark or lit all day.
Understanding this layout matters because the symptom tells you where the problem probably sits. All poles dark points toward the control or the feeder. One pole dark points toward that fixture, its lamp or driver, or its fuse. A group of poles dark on the same side points toward a break in the underground run feeding that section. Describing the pattern clearly to the dispatcher saves a technician a lot of time when they arrive.
Photocell and control failures
The photocell is the most common reason an entire lot goes dark or stays lit through the day. These sensors are small, exposed to sun, rain and salt air, and they wear out. When a photocell fails, it can fail in either direction. Some fail open and keep the lights off, others fail closed and keep them on around the clock. A lot that is lit at noon is as much a symptom as a lot that is dark at night.
Another control problem is the contactor, a heavy-duty relay that switches the lighting circuit. Contactors can burn contacts, buzz, chatter or stick. A technician will check whether the contactor coil is receiving a signal and whether the contacts are passing power to the load side. Time clocks and building automation settings can also be reset by a power blip or a storm, so a lot may go dark because the schedule has been lost rather than because anything is broken.
From the outside, a manager can note a few things without touching anything. Is the lot dark at all hours or only at night. Did it go dark after a storm or a brief power flicker. Do the poles come on briefly and then go off. Does the building signage or exterior wall lighting, which may be on the same control, behave the same way. Those observations help the technician decide whether to start at the sensor, the contactor, or the feeder.
- Lights on during the day usually suggest a failed photocell, a stuck contactor, or a bypass switch left in the wrong position.
- Lights off at night with the building lit suggests a control, breaker or feeder problem on the lighting circuit.
- Lights that cycle on and off suggest a weak sensor, a failing driver or a loose connection.
- A schedule that reset after a power event may only need to be reprogrammed by someone who knows the controller.
Feeder faults and breaker trips
The feeder is the set of conductors that carries power from the building to the poles. When a feeder fails, a whole section or the whole lot loses power. The first sign is often a tripped breaker in the lighting panel, and a manager may be tempted to reset it. One careful reset by a trained staff member who already knows the panel is one thing. Repeated resets of a breaker that keeps tripping are another, because the breaker is doing its job by stopping a fault, and forcing it back on can damage equipment or create a hazard.
A breaker that trips immediately points toward a short circuit or a ground fault somewhere on that circuit, such as water in a pole base, damaged wire insulation, or a failed fixture. A breaker that trips after the lights have been on for a while can point to an overloaded circuit, a failing driver, or a fault that develops as wiring heats up. Either way, the technician will want to isolate the circuit, test the insulation with proper instruments, and divide the run into sections to find the bad one.
If the breaker will not reset at all, or if there is any burning smell, discoloration, or heat at the panel, leave it alone and say so on the phone. If there is smoke or flames, that is a 911 call. Keep people away from the panel and do not open covers or try to inspect inside it.
Underground faults and why they take time
Many lot lighting runs are buried in conduit under asphalt or landscaping. Over time, water can get into the conduit, insulation can break down, and the ground can shift. Vehicles, utility work and tree roots can also damage a buried run. When the cable is damaged underground, the symptom is often a breaker that trips, a ground fault, or a section of poles that simply will not light.
Finding the fault is a diagnostic job, not a guess. A technician may measure insulation resistance on the conductors, open pole bases to see where power stops, and test sections one at a time. If the break is in the conduit, repair may involve pulling new conductors through the existing conduit, splicing in a proper waterproof junction, or trenching to replace a section. Which of those is needed depends on what is found, and it is not something anyone can responsibly decide from the outside.
This is also the reason a fast temporary measure may be discussed. In some cases a technician can disconnect the faulted section, restore power to the poles that are healthy, and plan the permanent repair for a separate visit. Whether that is possible depends on how the circuits are arranged and on what the technician finds. Quotes for this kind of work are given by phone after the situation is described, and bigger jobs need an on-site look.
Pole base, handhole and fixture problems
Each pole has parts that wear out. The handhole cover can be missing or loose, which lets water, insects and debris in. The fuse holder inside the base can corrode, particularly in South Florida where humidity and salt air are common. Wire connections can loosen from vibration or heat. Inside the head, the driver or ballast, the part that regulates power to the lamp, can fail even when the lamp itself is fine.
Modern LED fixtures have their own failure patterns. The driver is a power electronics module and it can fail after a surge or from heat. A fixture can flicker, dim, or go out entirely. Older high-intensity discharge fixtures can fail to restart after a brief power interruption because the lamp needs time to cool before it will strike again, which may look like a failure when it is only a delay.
A pole that has been struck by a vehicle deserves extra caution. Even a small impact can crack the base, loosen the anchor bolts, or damage wiring inside. If a pole is leaning, keep people away and tell the dispatcher. Do not try to straighten it or push it back. A technician and, where needed, a contractor with the right equipment should assess it before anyone is allowed near.
- Missing or cracked handhole covers: note which poles and report them.
- Visible rust at the base, a pole that moves or leans, or exposed bolts: keep people away.
- One pole out in a row: probably the fixture, its driver or its fuse.
- Poles that flicker in rain: water getting in somewhere along the run.
Storms, surges and salt air
In South Florida, weather is a frequent cause of lighting trouble. Lightning near a property can send a surge through the wiring and damage drivers or controllers. Heavy rain finds its way into poorly sealed bases and junction boxes. During hurricane season, high wind can damage poles, tilt fixtures and pull on wiring, and flooding can reach lighting panels, pull boxes and underground conduits.
Salt air accelerates corrosion on fasteners, covers, fuse holders and lug connections. This does not usually cause a sudden failure, but it makes small problems more likely over time, and it is a common reason a lot works for years and then fails after a particularly wet week. A technician who sees heavy corrosion will often recommend repairing or replacing the affected hardware as part of the job, because a quick fix on top of a corroded connection tends to be short-lived.
After a storm, do not walk the lot looking for damage near leaning poles or broken fixtures. A wire can be energized and invisible in standing water. If water is on the pavement near a pole base, a pull box or a lighting panel, treat the area as hazardous. Report what you saw from a safe distance and let the technician decide how to proceed. For broader storm guidance see after-storm power restoration safety.
Liability and the paper trail
A dark lot is not only an inconvenience. Property owners and managers are generally expected to keep common areas reasonably safe, and poor lighting can become part of a dispute if someone is injured or a vehicle is damaged. This page cannot give legal advice and does not make claims about what any policy or law requires. What it can say is that careful records are useful to the people who have to answer questions later.
Write down when the outage was first noticed, who noticed it, what was done to keep people safe, and when the electrician was called. Take photographs of the dark lot from a safe distance, of any visible damage, and of the status of the signs, posts or barriers you put up. Save the technician's findings in writing. If the cause turns out to be a failed component, a damaged underground run, or a utility problem, the report should say so.
If the property is leased, the lease may say who is responsible for common area lighting, and that can vary. Read it, and talk to the landlord or property manager. We cover this in more detail on the page about who handles a power problem in a commercial lease, and about documenting a business outage.
What to check safely before you call
There are a few observations anyone on site can make without touching equipment. Walk the building, not the lot if conditions are unsafe, and look at whether the pattern of darkness is uniform. Check whether the building's exterior lighting, signs and security cameras are on. Note whether other businesses nearby are dark, which would suggest the utility. Look for obvious storm damage, vehicle damage to a pole, or water pooled near a pole base, all from a distance.
If you have a person on staff who is authorized to operate the lighting panel and who knows the panel, they can look at the breaker position without opening any cover or removing any part. A breaker that is in the tripped or middle position gives the electrician a useful fact. Do not repeatedly reset it, and do not bypass the photocell or contactor with anything.
Never climb a pole, open a pole base, remove a handhole cover, or lift a fixture. Never use water on a fixture or around an electrical box. Do not cut or move wires. Do not park or drive a vehicle in a way that puts you near a downed or leaning pole. If any of those steps looks necessary, it is a job for a qualified electrician with the proper equipment.
- Make sure people are safe and that no wires are down or smoking.
- Check whether the building and neighbors have power.
- Note which poles are dark and whether any are lit.
- Note the time the outage started and any weather or impact events.
- Take photographs from a safe distance.
- Call, and describe what you saw in plain terms.
What the technician will check
A technician arriving for a lot lighting call will start with safety. They will look at the site, check for hazards, and confirm what is dark and what is lit. They will usually start at the source, the lighting panel and the control, and work outward. That means checking breakers, the contactor, the photocell or time clock, and measuring voltage at the load side.
From there, the work usually becomes a process of elimination. If the control is working and power leaves the panel, the technician moves to the first pole and checks power there, then to the next pole, and so on until power stops. At the point where it stops, they look for a blown fuse, a bad connection, damaged conductors or a failed fixture. When the fault is on the buried part, they may test insulation to see whether the cable is leaking to ground.
Be ready for the technician to give you a plain explanation of what they found, what is safe to do tonight, and what a permanent repair would involve. Some jobs are done in one visit. Others need parts, a second visit, or work by a specialist contractor. If a pole needs to be replaced, or if trenching and permits are involved, that is a bigger project. Ask the technician to put findings in writing.
Temporary lighting and what is realistic
Sometimes a lot cannot be fully repaired right away. In that case, the useful question is what temporary arrangement will keep people safe. Options sometimes discussed include restoring the healthy poles and isolating the faulty ones, adding portable lighting supplied by a rental company, or restricting use of part of the lot. Each has limits, and none of them should involve loose cords across pavement or improvised connections to building outlets.
Portable lighting needs its own safe power source, and extension cords laid across traffic lanes are a trip and fire hazard. If you plan to use temporary towers or lights, ask the electrician how they should be powered. Do not assume that it is safe to connect them to an exterior outlet that may be on a circuit already shared with other loads or with a damaged feeder.
Remember that restoring only some of the poles can leave dark gaps where people still have to walk. Be honest about that and keep the staff or security plan in place. The goal is to avoid an incident while the permanent repair is arranged. Our temporary power restoration page explains how temporary measures work in general.
Preventing the next outage
After the lot is lit again, take the opportunity to ask what the technician saw that could be improved. A lot that has failed because of a corroded fuse holder or a missing handhole cover may have other poles with the same weakness. A periodic walk through during daylight, looking at cover plates, pole bases, signs of water, and fixtures that flicker, helps find small problems early.
Keep a simple map or list of the poles with the circuit each belongs to. If the lighting panel is not labeled, ask the technician to label it as part of the visit. That list will save time at the next outage. Keep a note of the type of fixture and photocell used, since parts and controls vary and a quick replacement is easier when you know what is installed.
Planning cannot ensure that nothing will ever fail. Lamps, drivers and sensors wear out, and weather is unpredictable. What planning does is make the next visit shorter and less stressful. If you want a more systematic approach, read electrical checks that support business continuity, and when you are ready, call and talk through the situation.
Calling for help
When you call, describe what you see in plain terms. Say whether the lot is fully or partly dark, whether the building has power, and whether any pole is damaged or leaning. Say whether there was a storm, an impact or a power flicker before the outage. Mention any smell of burning, noise from the panel, or tripped breakers. Say clearly if the area is closed and whether people are on site.
The dispatcher will explain the service call charge before anyone is sent, and any quote for repair is given by phone or after an on-site visit, never by text on a website. Be ready to give the address, a contact person on site, and details on access, such as gates, alarms, and where the lighting panel is. If the property is managed, have the manager's contact available.
If anyone is hurt, if a wire is down, or if you see smoke or flames, call 911 first. For a dark lot that is otherwise stable, call and tell the dispatcher what you know. We will help you work out the next safe step.
Questions people ask
Who do I call if only the parking lot lights are out?
If the building has power and only the lot is dark, the fault is on the private side of the meter, which is an electrician's job. If the whole building and neighbors are dark too, call the power company's outage line. If a pole is down, a wire is on the ground, or there is smoke or fire, call 911 first and keep everyone back from the area.
Can I reset the breaker for the lot lights myself?
A trained staff member who already knows the panel may look at the breaker and reset it once. If it trips again, stop. A breaker that keeps tripping is protecting the circuit from a fault, and repeated resets can cause damage or create a hazard. Never open the panel cover, never bypass the breaker, and tell the dispatcher what you saw.
Why are the lot lights on during the day?
Daytime operation usually points to a failed photocell, a stuck contactor, a manual bypass left on, or a controller that lost its schedule. It is not an emergency by itself, but it wastes power and shortens fixture life. Describe the pattern to the electrician, and avoid touching the control equipment or covering the sensor with tape or other materials.
Why would one pole be dark while the others are lit?
A single dark pole most often means a failed lamp or driver in that fixture, a blown fuse in the pole base, or a loose connection. Poles are usually wired in a string, so a break farther along can also affect poles beyond it. A technician will test at the pole base. Do not open the base or climb the pole yourself.
A vehicle hit a light pole. What should I do?
Keep everyone away from the pole and the ground around it, and call 911 if anyone is hurt or if wires may be exposed. Do not touch or push the pole. A struck pole can have cracked anchors and damaged wiring even if it looks upright. Report the damage to the electrician so they can assess it safely before the pole is touched.
Is a dark parking lot my responsibility as the property owner?
Responsibility depends on ownership, the lease, and local rules, and this page cannot give legal advice. In general, common area lighting is something owners and managers are expected to address promptly. Keep records of when you noticed the outage, what you did to keep people safe, and when you called. Read your lease and speak with the landlord or an attorney if you are unsure.
If "Parking Lights: What to Know and Do" matches what is happening, call and describe it plainly: the room, the breaker, any burning smell or tripped circuit. We explain what the repair would involve before a visit is set.
Related pages
- Exit Lights: Exit signs dark or emergency lights failing in an occupied building? Learn why it is a life-safety issue, safe first steps, and what a technician will check.
- Business Power Loss: Your business just lost power. Follow a safe first-hour sequence for owners and managers: safety, isolating the cause, informing staff, and documenting.
- Tenant and Landlord: Power out at a leased business space? Learn how responsibility is usually divided between tenant and landlord, and why the lease comes first.
- Temporary Power: When a full electrical repair has to wait, isolating the damaged part can keep the rest of the home running. Learn how temporary power is done and its limits.
- Outage Records: What to record during a business power outage for managers, landlords and insurers: timelines, photos, losses and technician findings, with no coverage claims.
- Restaurant Kitchen: When a restaurant kitchen loses power, hood, walk-in and line equipment circuits all matter, and so does food safety timing. See safe steps and what to tell us.
